![background image](http://html1.mh-extra.com/html/makita/dst110rtj/dst110rtj_instruction-manual_4283173004.webp)
4
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
ENE054-1
The tool is intended for pressing staples into construction
materials such as timbers.
General Power Tool Safety
Warnings
GEA010-1
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS STAPLER SAFETY
WARNINGS
GEB075-2
1.
Always assume that the tool contains fasteners.
Careless handling of the stapler can result in
unexpected firing of fasteners and personal injury.
2.
Do not point the tool towards yourself or anyone
nearby.
Unexpected triggering will discharge the
fastener causing an injury.
3.
Do not actuate the tool unless the tool is placed
firmly against the workpiece.
If the tool is not in
contact with the workpiece, the fastener may be
deflected away from your target.
4.
Disconnect the tool from the power source when
the fastener jams in the tool.
While removing a
jammed fastener, the stapler may be accidentally
activated if it is plugged in.
5.
Use caution while removing a jammed fastener.
The mechanism may be under compression and the
fastener may be forcefully discharged while
attempting to free a jammed condition.
6.
Do not use this stapler for fastening electrical
cables.
It is not designed for electric cable installation
and may damage the insulation of electric cables
thereby causing electric shock or fire hazards.
7.
Always wear safety goggles or safety glasses with
side shield, and a full face shield when needed.
8.
Keep hands and feet away from the ejection port
area.
9.
Always remove the battery cartridge before
loading the fasteners, adjustment, inspection,
maintenance or after operation is over.
10.
Make sure no one is nearby before operation.
Never attempt to drive fasteners from both the
inside and outside of wall at the same time.
Fasteners may rip through and/or fly off,
presenting a grave danger.
11.
Watch your footing and maintain your balance
with the tool. Make sure there is no one below
when working in high locations.
12.
Check walls, ceilings, floors, roofing and the like
carefully to avoid possible electrical shock, gas
leakage, explosions, etc. caused by stapling into
live wires, conduits or gas pipes.
13.
Use only fasteners specified in this manual. The
use of any other fasteners may cause malfunction
of the tool.
14.
Do not tamper with the tool or attempt to use it for
other than driving fasteners.
15.
Do not operate the tool without fasteners. It
shortens the service life of the tool.
16.
Stop driving operations immediately if you notice
something wrong or out of the ordinary with the
tool.
17.
Never fastener into any materials which may allow
the fastener to puncture and fly through as a
projectile.
1.
Red indicator
2.
Button
3.
Battery cartridge
4.
Trigger
5.
Lever
6.
Sub magazine
7.
Locking lever
8.
Press
9.
Main magazine
10. Staples
11. Groove
12. Hook
13. Screw
14. Material
15. View window
16. Pusher
Model
DST110
Staple width
10 mm
Applicable staples length
7 mm - 10 mm
Staple magazine capacity
125 pcs
Dimensions (L x W x H)
245 mm x 79 mm x 191 mm
Net weight
2.0 kg
Rated voltage
D.C. 14.4V