![background image](http://html1.mh-extra.com/html/makita/dls714z/dls714z_instruction-manual_4217886012.webp)
12 ENGLISH
Noise
The typical A-weighted noise level determined accord
-
ing to EN61029:
Sound pressure level (L
pA
) : 88 dB(A)
Sound power level (L
WA
) : 97 dB (A)
Uncertainty (K) : 3 dB(A)
WARNING:
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN61029:
Vibration emission (a
h
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
Makita declares that the following Machine(s):
Designation of Machine: Cordless Slide Compound
Miter Saw
Model No./ Type: DLS714
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents: EN61029
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
16.1.2015
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
General power tool safety warnings
WARNING:
Read all safety warnings and
all instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cordless miter saw safety warnings
1.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
2.
Check the saw blade carefully for cracks or
deformation before operation.
Replace damaged blades immediately.
3.
Replace the kerf board when worn.
4.
Use only saw blades specified by the manufac
-
turer which conform to EN847-1.
5.
Do not use saw blades manufactured from
high speed steel.
6.
Wear eye protection.
7.
Wear hearing protection to reduce the risk of
hearing loss.
8.
Wear gloves for handling saw blade (saw
blades shall be carried in a holder wherever
practicable) and rough material.
9.
Connect miter saws to a dust collecting device
when sawing.
10.
Select saw blades in relation to the material to
be cut.
11.
Always secure all moving portions before car-
rying the tool. When lifting or carrying the tool,
do not use the guard as a carrying handle.
12.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard does
not move freely and close instantly. Never clamp
or tie the blade guard into the open position.
13.
Keep the floor area free of loose material e.g.
chips and cut-offs.
14.
Use only saw blades that are marked with a
maximum speed equal to or higher than the no
load speed marked on the tool.
15.
When the tool is fitted with a laser or LED, do
not replace the laser or LED with a different
type.
Ask an authorized service center for repair.
16.
Never remove any cut-offs or other parts of the
workpiece from the cutting area whilst the tool
is running with an unguarded saw blade.
17.
Do not perform any operation freehand.
The
workpiece must be secured firmly against the turn
base and guide fence with the vise during all opera-
tions. Never use your hand to secure the workpiece.
18.
Ensure that the tool is stable before each cut.
19.
Fix the tool to a work bench, if needed.
20.
Support long workpieces with appropriate
additional supports.
21.
Never cut so small workpiece which cannot be
securely held by the vise.
Improperly held workpiece
may cause kickback and serious personal injury.
22.
Never reach around saw blade.
23.
Turn off tool and wait for saw blade to stop
before moving workpiece or changing
settings.
Содержание DLS714Z
