5
Model DKP140
Work mode : planing softwood
Vibration emission (a
h
) : 3.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model DKP180
Work mode : planing softwood
Vibration emission (a
h
) : 4.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
ENG901-1
•
The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
•
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
•
The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
•
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-16
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible manufacturer
declare that the following Makita machine(s):
Designation of Machine:
Cordless Planer
Model No./ Type: DKP140, DKP180
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by:
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
06.06.2013
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
GEA010-1
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for
future reference.
GEB064-2
CORDLESS PLANER SAFETY
WARNINGS
1.
Wait for the cutter to stop before setting the
tool down.
An exposed rotating cutter may
engage the surface leading to possible loss of
control and serious injury.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable
platform.
Holding the work by your hand or
against the body leaves it unstable and may lead
to loss of control.
3.
Rags, cloth, cord, string and the like should
never be left around the work area.
4.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
5.
Use only sharp blades. Handle the blades very
carefully.
6.
Be sure the blade installation bolts are
securely tightened before operation.
7.
Hold the tool firmly with both hands.
8.
Keep hands away from rotating parts.
9.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
10.
Make sure the blade is not contacting the
workpiece before the switch is turned on.
11.
Wait until the blade attains full speed before cutting.
12.
Always switch off and wait for the blades to
come to a complete stop before any adjusting.
13.
Never stick your finger into the chip chute.
Chute may jam when cutting damp wood.
Clean out chips with a stick.
14.
Do not leave the tool running. Operate the tool
only when hand-held.
15.
Always change both blades or covers on the
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
16.
Use only Makita blades specified in this manual.
17.
Always use the correct dust mask/respirator for
the material and application you are working with.
SAVE THESE INSTRUCTIONS.
Содержание DKP180RFE
Страница 83: ...83 ...
Страница 84: ...84 Makita Corporation Anjo Aichi Japan www makita com 885273 965 ...
