![background image](http://html1.mh-extra.com/html/makita/dhs783/dhs783_instruction-manual_4119435022.webp)
22 ENGLISH
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
CAUTION:
Clean out the upper and lower guards
to ensure there is no accumulated sawdust which may
impede the operation of the lower guarding system.
A
dirty guarding system may limit the proper operation which
could result in serious personal injury. The most effective
way to accomplish this cleaning is with compressed air.
If
the dust is being blown out of the guards, be sure the
proper eye and breathing protection is used.
CAUTION:
After each use, wipe off the saw
dust on the tool.
Fine saw dust may come inside the
tool and cause malfunction or a fire.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Adjusting 0°-cut or 45°-cut accuracy
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1.
Loosen the clamping screws on the front and rear
of the tool so that the bevel angle can be changed. Set
the stopper to 0° - 45° bevel angle position if you are
going to adjust 45°-cut accuracy.
►
Fig.47:
1.
Stopper
2.
Make the base perpendicular or 45° to the circular saw
blade using a triangular rule by turning the adjusting screw with a
hex wrench. You can also use a square rule to adjust 0° angle.
►
Fig.48:
1.
Triangular rule
►
Fig.49:
1.
Adjusting screw for 0° angle
2.
Adjusting
screw for 45° angle
3.
Tighten the clamping screws and then make a test
cut to check if desired angle is obtained.
Adjusting the parallelism
CAUTION:
Keep the parallelism accurate.
Otherwise the circular saw blade may bite into the
guide rail and the damaged guide rail may cause an
injury.
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1.
Set the tool to the maximum cutting depth.
2.
Make sure all levers and screws are tightened.
3.
Loosen the screws shown in the figure.
4.
While opening the lower guard, move the rear of
the base so that the distance A and B becomes equal.
►
Fig.50:
1.
Screw
2.
Base
5.
Tighten the screws and make a test cut to check
the parallelism.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard
-
ing these accessories, ask your local Makita Service
Center.
•
Circular saw blade
•
Rip fence (Guide rule)
• Hook
•
Guide rail
•
Bevel guide
• Clamp
• Sheet
•
Rubber sheet
•
Position sheet
•
Dust nozzle
•
Hex wrench
•
Wireless unit (for DHS783)
•
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
Содержание DHS783
