![background image](http://html1.mh-extra.com/html/makita/dhs630rtj/dhs630rtj_instruction-manual_4076112009.webp)
9
Loosen the lever on the side of the rear handle and
move the base up or down. At the desired depth of cut,
secure the base by tightening the lever.
For cleaner, safer cuts, set cut depth so that no more
than one blade tooth projects below workpiece. Using
proper cut depth helps to reduce potential for dangerous
kickback which can cause personal injury.
Bevel cutting
Fig.4
Loosen the wing screw on the front and rear base. Set
for the desired angle (0° - 45°) by tilting accordingly, then
tighten the wing screw securely.
Sighting
Fig.5
For straight cuts, align the 0° position on the front of the
base with your cutting line. For 45° bevel cuts, align the 45°
position with it. The position of the top guide is adjustable.
Switch action
Fig.6
CAUTION:
•
Before installing the battery cartridge into the tool,
always check to see that the switch trigger
actuates properly and returns to the "OFF" position
when released.
•
Do not pull the switch trigger hard without pressing
the lock-off lever. This can cause switch breakage.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided. To start the tool,
press the lock-off lever and pull the switch trigger.
Release the switch trigger to stop.
WARNING:
•
For your safety, this tool is equipped with lock-off
lever which prevents the tool from unintended
starting. NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the
lock-off lever. Return tool a MAKITA service center
for proper repairs BEFORE further usage.
•
NEVER tape down or defeat purpose and function
of lock-off lever.
Lighting the lamp
CAUTION:
•
Do not look in the light or see the source of light
directly.
Fig.7
Only to turn on the light, pull the switch trigger without
pressing the lock-off lever. To turn on the light and run
the tool, press the lock-off lever and pull the switch
trigger with the lock-off lever being pressed.
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it may
lower the illumination.
•
Do not use gasoline, thinner or the like to clean the
lens of lamp. Using such substances will damage
the lens.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
Removing or installing saw blade
CAUTION:
•
Be sure the blade is installed with teeth pointing up
at the front of the tool.
•
Use only the Makita wrench to install or remove the
blade.
Fig.8
To remove the blade, press the shaft lock so that the
blade cannot revolve and use the wrench to loosen the
hex bolt counterclockwise. Then remove the hex bolt,
outer flange and blade.
To install the blade, follow the removal procedure in
reverse. BE SURE TO TIGHTEN THE HEX BOLT
CLOCKWISE SECURELY.
Fig.9
When changing blade, make sure to also clean upper
and lower blade guards of accumulated sawdust. Such
efforts do not, however, replace the need to check lower
guard operation before each use.
Hex wrench storage
Fig.10
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
Connecting a vacuum cleaner
(for European countries only)
Fig.11
Fig.12
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Install the
dust nozzle on the tool using the screw. Then connect a
hose of the vacuum cleaner to the dust nozzle as shown
in the figure.
OPERATION
CAUTION:
•
Always insert the battery cartridge all the way until
it locks in place. If you can see the red part on the
upper side of the button, it is not locked completely.
Insert it fully until the red part cannot be seen. If not,
it may accidentally fall out of the tool, causing injury
to you or someone around you.
•
Be sure to move the tool forward in a straight line
gently. Forcing or twisting the tool will result in
Содержание DHS630RTJ
Страница 3: ...3 13 012108 1 2 14 012109 1 2 15 012102 1 2 16 012103 A B 1 2 3 17 012101 1 18 001145 1 2 19 012114 ...
Страница 66: ...66 ...
Страница 67: ...67 ...
Страница 68: ...68 Makita Corporation Anjo Aichi Japan www makita com 885270 973 ...