background image

2

ENGLISH

SPECIFICATIONS

Model:

DHR183

Drilling capacities

Concrete

18 mm

Steel

13 mm

Wood

24 mm

No load speed

0 - 1,100 min

-1

Blows per minute

0 - 5,000 min

-1

Overall length (with BL1860B)

288 mm

Rated voltage

D.C. 18 V

Net weight

2.1 - 2.9 kg

Optional accessory

Model:

DX16

Suction performance

0.24 l/min

Operating stroke

Up to 105 mm

Suitable drill bit

Up to 165 mm

Net weight

0.77 kg

• 

Due to our continuing program of research and development, the specifications herein are subject to change 

without notice.

• 

Specifications may differ from country to country.

• 

The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi

-

est combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge

BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger

DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / 

DC18SH / DC18WC

• 

Some of the battery cartridges and chargers listed above may not be available depending on your region of 

residence.

WARNING:

 

Only use the battery cartridges and chargers listed above.

 Use of any other battery cartridges 

and chargers may cause injury and/or fire.

Recommended cord connected power source

Portable power pack

PDC01

• 

The cord connected power source(s) listed above may not be available depending on your region of residence.

• 

Before using the cord connected power source, read instruction and cautionary markings on them.

Symbols

The followings show the symbols which may be used 

for the equipment. Be sure that you understand their 

meaning before use.

Read instruction manual.

 

Ni-MH
Li-ion

Only for EU countries

Due to the presence of hazardous com-
ponents in the equipment, waste electrical 
and electronic equipment, accumulators 

and batteries may have a negative impact 

on the environment and human health.
Do not dispose of electrical and electronic 
appliances or batteries with household waste!
In accordance with the European Directive 
on waste electrical and electronic equipment 
and on accumulators and batteries and 
waste accumulators and batteries, as well as 
their adaptation to national law, waste elec-
trical equipment, batteries and accumulators 

should be stored separately and delivered 

to a separate collection point for municipal 
waste, operating in accordance with the 
regulations on environmental protection.

This is indicated by the symbol of the 

crossed-out wheeled bin placed on the 
equipment.

Содержание DHR183RTJ





















Отзывы: