![background image](http://html.mh-extra.com/html/makita/dhk180rtj/dhk180rtj_instruction-manual_230359007.webp)
7 ENGLISH
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION:
When not operating the tool,
depress the trigger-lock button from side to
lock the switch trigger in the OFF position.
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided. To start the tool,
depress the trigger-lock button from A ( ) side and pull
the switch trigger. Tool speed is increased by increas
-
ing pressure on the switch trigger. Release the switch
trigger to stop. After use, depress the trigger-lock button
from B ( ) side.
►
Fig.3:
1.
Trigger-lock button
2.
Switch trigger
Using the trigger-lock button for
continuous operation
For continuous operation, depress the trigger-lock but
-
ton from B ( ) side while pulling the switch trigger, and
then release the switch trigger. To stop the tool, depress
the trigger-lock button from A ( ) side.
►
Fig.4:
1.
Trigger-lock button
2.
Switch trigger
Speed adjusting dial
►
Fig.5:
1.
Speed adjusting dial
The blows per minute can be changed by turning the
speed adjusting dial to a given number setting from 1 to
5. Higher speed is obtained when the dial is turned in
the direction of number 5. And lower speed is obtained
when it is turned in the direction of number 1.
Refer to the table for the relationship between the num
-
ber settings on the dial and the blows per minute.
Number
Blows per minute
1
1,000 min
-1
2
1,300 min
-1
3
1,900 min
-1
4
2,700 min
-1
5
3,200 min
-1
CAUTION:
Do not turn the adjusting dial when
the tool is running. Failure to do so may result in
the loss of control of the tool and cause an injury.
NOTICE:
The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1, or the speed adjusting function may no
longer work.
Lighting up the front lamp
►
Fig.6:
1.
Lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Electronic function
The tool is equipped with the electronic functions for
easy operation.
•
Constant speed control
The speed control function provides the constant
rotation speed regardless of load conditions.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Grease
Coat the shank end of the bit beforehand with a small
amount of grease (about 0.5 - 1 g). This chuck lubrica
-
tion assures smooth action and longer service life.
Installing or removing bit
Clean the shank end of the bit and apply grease before
installing the bit.
►
Fig.7:
1.
Shank end
2.
Grease
Insert the bit into the tool. Turn the bit and push it in until
it engages. After installing the bit, always make sure
that the bit is securely held in place by trying to pull it
out.
►
Fig.8:
1.
Bit
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
►
Fig.9:
1.
Bit
2.
Chuck cover
Bit angle
The bit can be secured at 12 different angles. To
change the bit angle, slide the change ring forward,
then turn the change ring to change the bit angle. At the
desired angle, slide the change ring back to the original
position. The bit will be secured in place.
►
Fig.10:
1.
Change ring
Содержание DHK180RTJ
Страница 2: ...1 2 3 Fig 1 1 2 Fig 2 1 2 A B Fig 3 1 2 A B Fig 4 1 Fig 5 1 Fig 6 1 2 Fig 7 1 Fig 8 2 ...
Страница 3: ...1 2 Fig 9 1 Fig 10 1 Fig 11 Fig 12 3 2 1 Fig 13 1 2 3 Fig 14 Fig 15 3 ...
Страница 68: ...IDE 885744 506 31 10 2019 Makita Europe N V Jan Baptist Vinkstraat 2 3070 Kortenberg Belgium ...