background image

R

epair

It is not required to lubricate the gear section because the portion is replaced as a factory- lubricated gear unit.

[3] DISASSEMBLY/ASSEMBLY

[3] -1. Drill Chuck

[1] NECESSARY REPAIRING TOOLS

CAUTION: Repair the machine in accordance with “Instruction  manual” or “Safety instructions”.

Code No.

Description

Use for

1R359 Drill chuck removing tool

[2] LUBRICATION

DISASSEMBLING

Hex wrench 10

(Use this tool if Drill chuck cannot be removed by the method of

  described in “[3]-1 Drill chuck disassembling”.)

removing/ mounting Drill chuck

Fig. 1

M6x22 Flat head screw

(Left handed thread)

Note

: It is required to remove Drill chuck when replacing Gear assembly, but you need not when replacing

          the parts that are independent of Gear assembly.

(1) Remove M6x22 Flat head screw. (

Fig. 1

)

(2) Preset the machine. (

Fig. 2

)    And set Hex wrench 10 to Vise. (

Fig. 3

)

(3) While holding Hex wrench 10 with Drill chuck firmly, remove Drill chuck from Gear assembly. (

Fig. 4

)

Fig. 2

Attach Battery. 

F/R change lever 

Set F/R Change lever

to 

Reverse

 (

counter-

clockwise

) rotation.  

Set Speed change lever

to Low speed mode

designated with 1. 

Speed change lever

Set Change ring

to Drill mode.  

Change ring

Open Drill chuck fully and remove M6x22

Flat head screw by turning it 

clockwise

CORRECT

WRONG

Fig. 3

Fig. 4

Setting of Hex wrench10 

Vise

Grip flat surfaces

of Hex wrench 10.

Hex wrench 10

Hex wrench 10,

viewed from side [A]

Vise

Hold the long end.

[A]

Do not hold edges

of Hex wrench 10.

Do not hold

the short end.

Hex wrench 10,

viewed from side [A]

Note

: Use Impact driver to unscrew

           M6x22 Flat head screw if it

           could not be removed

           manually. 

[A]

Clockwise

Counterclockwise

Hex wrench 10

Vise

Clockwise

*

1

 recoil force

of Machine   

Note: 

The rotational direction is viewed from operator.

1. Hold Hex wrench 10 with Drill chuck and grip Machine.

    Important

:

    Grip Machine tightly with both hands to provide

    the sufficient counterclockwise

*

2

 force against

    clockwise

*

1

 recoil force of Machine.

2. Pull Switch trigger slowly.

3. Spindle rotates counterclockwise

*

2

 and consequently

Drill chuck is removed from spindle.

Counterclockwise

*

2

 force to be applied by operator

 

P  

3

/ 1

1

Содержание BHP459












Отзывы: