background image

1

2

3

 

 

005719 

2.  Pull the trigger first and then place the contact 

element against the workpiece. 

• 

No. 1 method is for intermittent nailing, when you 
wish to drive a nail carefully and very accurately. No. 
2 method is for continuous nailing. 

• 

For No. 1 method, set the change lever to the 
"Intermittent Nailing" position. 
For No. 2 method, set the change lever to the 
"Continuous Nailing" position. 
After using the change lever to change the nailing 
method, always make sure that the change lever is 
properly set to the position for the desired nailing 
method. 

 

CAUTION: 

• 

However when the tool is set to the "Intermittent 
Nailing" mode, WITH THE TRIGGER HELD IN A 
HALF-PULLED POSITION, an unexpected nailing 
could occur, if contact element is allowed to 
re-contact against the workpiece or the other 
surface under the influence of recoil. 
In order to avoid this unexpected nailing, perform 
as follows; 

A.  Do not place the contact element against the 
workpiece with excessive force. 
B.  Pull the trigger fully and hold it on for 1-2 seconds 
after nailing. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Nailing mode change and trigger locking method 

1

2

3

4

 

 

005720 

For continuous nailing, set the change lever to the 
"Continuous Nailing" position. For intermittent nailing, set 
the change lever to the "Intermittent Nailing" position. To 
lock the trigger, set the change lever to the "Trigger Lock" 
position. Always make sure that the change lever is 
properly set to the position. 

 

CAUTION: 

• 

Operating the tool without nails shortens the life of 
the tool and should be avoided. 

Air exhaust 

1

 

 

005721 

Air exhaust direction can be changed easily by rotating 
the exhaust cover. Change it when necessary. 

Jammed nailer 

1

2

 

 

005722 

 

1. Hammer 
2. Small rod 

1. Exhaust cover 

1. Change lever 
2. Continuous 

nailing 

3. Trigger lock 
4. Intermittent 

nailing 

1. Trigger 
2. Contact element
3. Workpiece 

Содержание AN504













Отзывы: