Makita 9503BH Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 16

Makita 9503BH Скачать руководство пользователя страница 10

10

Unplug tool and place it upside down allowing easy access
to spindle. Remove any accessories on spindle. Thread wire
wheel brush onto spindle and tighten with the wrenches.
When using wire wheel brush, avoid applying too much pres-
sure which causes over bending of wires, leading to prema-
ture breakage.

Operation with abrasive cut-off wheel
(optional accessory)

WARNING:

•

When using an abrasive cut-off wheel, be sure to use
only the special wheel guard designed for use with cut-
off wheels.

•

NEVER use cut-off wheel for side grinding.

During  cutting  operations,  never  change  the  angle  of  the
wheel.  Placing  side  pressure  on  the  cut-off  wheel  (as  in
grinding)  will  cause  the  wheel  to  crack  and  break,  causing
serious personal injury.

MAINTENANCE

CAUTION:

•

Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.

The tool and its air vents have to be kept clean. Regularly
clean the tool

’

s air vents or whenever the vents start to

become obstructed.

Replacing carbon brushes

Remove  and  check  the  carbon  brushes  regularly.  Replace
when  they  wear  down  to  the  limit  mark.  Keep  the  carbon
brushes  clean  and  free  to  slip  in  the  holders.  Both  carbon
brushes should be replaced at the same time. Use only iden-
tical carbon brushes.

1. Lock nut
2. Abrasive cut-off wheel
3. Inner flange
4. Wheel guard for cut-off wheel

001616

1

3

2

4

1. Exhaust vent
2. Inhalation vent

2

1

001163

1. Limit mark

1

001145

«
...
8
9
10
11
12
...
»

Содержание 9503BH

















Отзывы:

Нет отзывов