4
ENGLISH
(Original instructions)
Explanation of general view
1
Lever
2
Scale
3
Depth guide
4
Clamping nut
5
Indication
6
Angle plate
7
Base
8
Top guide
9
Rip fence (Guide rule)
10
Switch trigger
11
Lock-off button
12
Hex wrench
13
Shaft lock
14
Hex bolt
15
Outer flange
16
Saw blade
17
Inner flange
18
Rear handle
19 Front handle
20 Vacuum cleaner
21 Adjusting screw
22 Triangular rule
23 Limit mark
24 Brush holder cap
25 Screwdriver
SPECIFICATIONS
Model
5104/5104S
Blade diameter .......................................... 260 – 270 mm
Max. cutting depth
at 0° ............................................................ 95/100 mm
at 45° ............................................................ 69/73 mm
No load speed (min
–1
) ............................................ 3,800
Overall length ...................................................... 405 mm
Net weight ............................................................. 9.2 kg
Safety class ..............................................................
/II
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
ENE028-1
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
GEB013-3
CIRCULAR SAW SAFETY WARNINGS
Danger:
1.
Keep hands away from cutting area and the
blade. Keep your second hand on auxiliary
handle, or motor housing.
If both hands are
holding the saw, they cannot be cut by the blade.
2.
Do not reach underneath the workpiece.
The
guard cannot protect you from the blade below the
workpiece.
3.
Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth
should be visible below the workpiece.
4.
Never hold piece being cut in your hands or
across your leg. Secure the workpiece to stable
platform.
It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
5.
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and shock the
operator.
6.
When ripping always use a rip fence or straight
edge guide.
This improves the accuracy cut and
reduces the chance of blade binding.
7.
Always use blades with correct size and shape
(diamond versus round) of arbour holes.
Blades
that do not match the mounting hardware of the saw
will run eccentrically, causing loss of control.
8.
Never use damaged or incorrect blade washers
or bolt.
The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
9.
Causes and Operator Prevention of Kickback:
– kickback is a sudden reaction to a pinched, bound
or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the
operator;
– when the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator;
– if the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can dig
into the top surface of the wood causing the blade
to climb out of the kerf and jump back toward the
operator.
A typical illustration of proper hand support, work-
piece support, and supply cord routing (if applicable).
