![background image](http://html.mh-extra.com/html/makita/4334d/4334d_instruction-manual_223615009.webp)
CAUTION:
• The battery charger Model DC1801 is for charging Makita battery cartridge. Never use it for other purposes
or for other manufacturer’s batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of
time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can
recharge the battery cartridge fully after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a
location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this
occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool
faster if you remove the battery cartridge from the battery charger.
• If the charging light flashes alternately in green and red color, a problem exists and charging is not possible.
The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or
damaged.
Trickle charge (Maintenance charge)
If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the
charger will switch into its ‘‘trickle charge (maintenance charge)’’ mode and keep the battery cartridge fresh and
fully charged.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely discharged.
Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F).
Let a hot battery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.
Selecting the cutting action (Fig. 3)
This tool can be operated with an orbital or a straight line cutting action.
To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below
to help determine the appropriate cutting action.
Position
Cutting action
Applications
O
Straight line cutting action
For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
I
Small orbit cutting action
For cutting mild steel, aluminum and hard wood.
II
Medium orbit cutting action
For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
III
Large orbit cutting action
For fast cutting in wood and plywood.
Switch action (Fig. 4)
CAUTION:
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the ‘‘OFF’’ position when
released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
depress the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
Speed adjusting dial (Fig. 5)
The tool speed can be adjusted and maintained
between 500 and 2,800 strokes per minute by turning
the adjusting dial. The dial is marked 1 (lowest speed)
to 5 (full speed).
Refer to the table below to select the proper speed for
the workpiece to be cut. However, the appropriate
speed may differ with the type or thickness of the
workpiece. In general, higher speeds will allow you to
cut workpieces faster but the service life of the blade
will be reduced.
4334D (E) (’100. 8. 28)
9
Содержание 4334D
