![background image](http://html.mh-extra.com/html/makita/4326/4326_instruction-manual_230074007.webp)
7
may differ with the type or thickness of the workpiece. In
general, higher speeds will allow you to cut workpieces
faster but the service life of the blade will be reduced.
Workpiece to be cut
Number on adjusting dial
Wood
5 - 6
Mild steel
3 - 6
Stainless steel
3 - 4
Aluminum
3 - 6
Plastics
1 - 4
006583
CAUTION:
•
If the tool is operated continuously at low speeds
for a long time, the motor will get overloaded and
heated up.
•
The speed adjusting dial can be turned only as far
as 6 and back to 1. Do not force it past 6 or 1, or
the speed adjusting function may no longer work.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Installing or removing saw blade
Fig.4
CAUTION:
•
Always clean out all chips or foreign matter
adhering to the blade and/or blade holder. Failure
to do so may cause insufficient tightening of the
blade, resulting in a serious personal injury.
•
Do not touch the blade or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
•
Always secure the blade firmly. Insufficient
tightening of the blade may cause blade breakage
or serious personal injury.
•
Use only B type blades. Using blades other than B
type blades causes insufficient tightening of the
blade, resulting in a serious personal injury.
To install the blade, loosen the bolt counterclockwise on
the blade holder with the hex wrench.
With the blade teeth facing forward, insert the blade into
the blade holder as far as it will go. Make sure that the
back edge of the blade fits into the roller. Then tighten
the bolt clockwise to secure the blade.
Fig.5
To remove the blade, follow the installation procedure in
reverse.
NOTE:
•
Occasionally lubricate the roller.
Hex wrench storage
Fig.6
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
Adjusting roller (For models 4326/4327)
Fig.7
Loosen the bolt on the back of the base with the hex
wrench. Move the retainer so that the roller contacts the
blade lightly. Then tighten the bolt to secure the base
and the retainer.
NOTE:
•
Occasionally lubricate the roller.
Dust cover
Fig.8
CAUTION:
•
Always wear safety goggles even when operating
the tool with the dust cover lowered.
Lower the dust cover to prevent chips from flying.
However, when making bevel cuts, raise it all the way.
OPERATION
CAUTION:
•
Always hold the base flush with the workpiece.
Failure to do so may cause blade breakage,
resulting in a serious injury.
•
Advance the tool very slowly when cutting curves
or scrolling. Forcing the tool may cause a slanted
cutting surface and blade breakage.
Turn the tool on without the blade making any contact
and wait until the blade attains full speed. Then rest the
base flat on the workpiece and gently move the tool
forward along the previously marked cutting line.
Fig.9
Bevel cutting
Fig.10
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before tilting the base.
•
Raise the dust cover all the way before making
bevel cuts.
With the base tilted, you can make bevel cuts at any
angle between 0° and 45° (left or right).
Loosen the bolt on the back of the base with the hex
wrench. Move the base so that the bolt is positioned in
the center of the cross-shaped slot in the base.
Fig.11
Tilt the base until the desired bevel angle is obtained.
The edge of the motor housing indicates the bevel angle
by graduations. Then tighten the bolt to secure the base.
Fig.12
Содержание 4326
Страница 73: ...73 ...
Страница 74: ...74 ...
Страница 75: ...75 ...
Страница 76: ...76 www makita com Makita Jan Baptist Vinkstraat 2 3070 Belgium Makita Corporation Anjo Aichi Japan 884727A969 ...