![background image](http://html.mh-extra.com/html/makita/3600h/3600h_instruction-manual_229998009.webp)
9 ENGLISH
Straight guide
►
Fig.6
The straight guide is effectively used for straight cuts
when chamfering or grooving.
►
Fig.7:
1.
Wing bolt (B)
2.
Guide bar
3.
Wing bolt (A)
4.
Straight guide
To install the straight guide, insert the guide bar into
the holes in the tool base until the notch in the guide
bar reaches just under the wing bolt (B). Then tighten
wing bolt (B). Loosen the wing bolt (A) and adjust the
distance between the bit and the straight guide. At the
desired distance, tighten the wing bolt (A) to secure the
straight guide in place.
When cutting, move the tool with the straight guide flush
with the side of the workpiece.
Templet guide
►
Fig.8
The templet guide provides a sleeve through which
the bit passes, allowing use of the tool with templet
patterns.
To install the templet guide, screw the templet guide on
the base plate.
►
Fig.9:
1.
Template guide
2.
Base plate
Secure the templet to the workpiece. Place the tool on
the templet and move the tool with the templet guide
sliding along the side of the templet.
►
Fig.10:
1.
Bit
2.
Base
3.
Templet
4.
Workpiece
5.
Distance (X)
6.
Outside diameter of the
templet guide
7.
Templet guide
NOTE:
•
The workpiece will be cut a slightly different
size from the templet. Allow for the distance (X)
between the bit and the outside of the templet
guide. The distance (X) can be calculated by
using the following equation:
Distance (X) = (outside diameter of the templet guide -
bit diameter) / 2
Trimmer guide
►
Fig.11
Trimming, curved cuts in veneers for furniture and the
like can be done easily with the trimmer guide. The
guide roller rides the curve and assures a fine cut.
►
Fig.12:
1.
Wing bolt (B)
2.
When the bit strikes the
trimmer guide, insert a piece of wood into
this space.
3.
Fine adjusting screw
4.
Wing
bolt (A)
5.
Trimmer guide
6.
Guide roller
7.
Wing bolt (C)
Install the trimmer guide on the tool base with the wing
bolts (B). Loosen the wing bolt (A) and adjust the dis
-
tance between the bit and the trimmer guide by turning
the fine adjusting screw (1.5 mm per turn). At the
desired distance, tighten the wing bolt (A) to secure the
trimmer guide in place. When adjusting the guide roller
up or down, loosen the wing bolt (C). After adjusting it,
tighten the wing bolt (C) securely.
►
Fig.13:
1.
Bit
2.
Guide roller
3.
Workpiece
When cutting, move the tool with the guide roller riding
the side of the workpiece.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspec
-
tion or maintenance.
•
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
Replacing carbon brushes
►
Fig.14:
1.
Limit mark
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
►
Fig.15:
1.
Brush holder cap
2.
Screwdriver
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per
-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
•
These accessories or attachments are recom
-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
Router bits
Straight bit
►
Fig.16
mm
D
A
L 1
L 2
6
1/4"
8
8
60
25
6
1/4"
6
1/4"
6
50
18
8
50
18
20
50
15
1/2"
12
1/2"
12
12
60
30
10
60
25
Содержание 3600H
