background image

R

epair

P 10 / 15

Fig. 13

Fig. 14

Fig. 15

[11] Adjustment of Ruler Ass'y

Parallel Adjusting Ruler Ass'y to Table

Loosen two M6x20 Hex. socket head screws out of three pieces on Ruler ass'y, pretighten the remaining screw located
in the front side. See Fig.13.
Push the part designated by     to stabilize the Ruler ass'y, and then fasten the two screws while aligning the Ruler ass'y
with a groove on Table.

Two M6x20 Hex. socket head screws: Loosened

Groove on Table

Main table

M6x20 Hex.
socket head screw: Pretightened

Ruler ass'y

[12] Parallel Adjusting Saw Blade

Align one of the grooves on Table with Ruler ass'y.
Slide the Ruler ass'y along with Saw blade.
Loosen the securing force of Adjust block in front of Frame, and then 
move Saw blade to either right or left side to align it with the Ruler 
ass'y.
Adjust block is accessible from the clearance around levers in Base front
cover by inserting a wrench 10 without upside down of the machine.
Frame can be moved while tapping the area designated by     with Flat
screwdriver as illustrated in Fig.15.

Adjusting Clamp Action of Ruler ass'y

Secure Sub table so as not to move by two Grips. 
As illustrated in Fig.14, loosen the Lever of the Ruler ass'y. And then fasten M5x25 Pan head screw to the limit using 
Phillips screwdriver. 
Next, loosen the M5x25 Pan head screw until the Ruler ass'y can slide smoothly on two rails without backlash.
Finally, fasten M5x655 Pan head screw so that the opposite end of the Ruler ass'y can not moved while clamping 
the main table by the Ruler ass'y.

M5x655 Pan head screw
in Ruler

Lever of Ruler ass'y
(out of locked position.)

The opposite end
of Ruler ass'y

M5x25 Pan head screw
in Ruler top holder

Phillips screwdriver

Flat
screwdriver

Frame

Saw blade

Содержание 2704
















Отзывы: