Makita 2416S, Инструкция по эксплуатации, Страница: 8 / 36

8 ENGLISH
Changing the width between vise
and guide
► Fig.6: 1. Socket wrench 2. Guide 3. Hex bolt 4. Vise
Changing guide position to accommodate larger work-
piece as shown, the socket wrench can be used to
remove the hex bolts and move the guide. The following
interval settings are possible:
0-170 mm (0 - 6-3/4")
60-230 mm (2-3/8" - 9")
a
a
a
a
80
a
110
a
a
Applicable wheel
dimensions
405 mm (16") outer dia. X less than 4.5 mm (3/16")
X 25.4 mm (1") inner dia.
Wheel configuration
Max. cutting
capacity
115mm
(4-1/2")
115mm
(4-1/2")
120 mm
(4-3/4")
110 mm
(4-3/8")
230 mm
(9")
110 mm
(4-3/8")
110 mm
(4-3/8")
110 mm
(4-3/8")
185 mm
(7-1/4")
150 mm
(5-7/8")
cut off
cut off
Setting the cutting angle
► Fig.7: 1. Socket wrench 2. Hex bolts 3. Guide
To change the cutting angle, loosen the hex bolts with
the socket wrench as shown, then move the guide to
the desired angle. At 60-230 mm (2-3/8" - 9") position,
the guide cannot be angle to allow 45°cuts.
CAUTION:
Tighten the hex bolts securely.
CAUTION:
Do not operate the tool when
the material is not firmly secured with the vise
because of the cutting angle.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Installing cut-off wheel
► Fig.8: 1. Thumb bolt 2. Knob 3. Center cap
1. To install a wheel, loosen the thumb bolt and lift up
the center cap with the knob.
2. Press stopper in the direction of the arrow. Loosen
the hex bolt with the socket wrench by turning it
counterclockwise. Then remove the hex bolt, outer
flange and wheel.
►
Fig.9: 1.
Stopper
2.
Socket wrench
3. To install the wheel, follow the removal procedure
in reverse. BE SURE TO TIGHTEN THE HEX
BOLT SECURELY. Secure center cap carefully
with thumb bolt.
CAUTION:
• When installing the wheel, make sure that
Makita mark on the wheel faces you on the
outside.
• Use only Makita socket wrench to remove or
install the wheel.
Storing socket wrench
► Fig.10: 1. Socket wrench
The socket wrench can be conveniently stored in the
location as indicated.
Securing workpiece
► Fig.11: 1. Vise plate 2. Vise nut 3. Vise handle
By turning the vise handle counterclockwise and then
flipping the vise nut to the left, the vise is released from
the shaft threads and can be moved rapidly in and out.
To grip workpieces, push the vise handle until the vise
plate contacts the workpiece. Flip the vise nut to the
right and then turn the vise handle clockwise to securely
retain the workpiece.
CAUTION:
• Always set the vise nut to the right fully when
securing the workpiece. Failure to do so may
result in insufficient securing of the workpiece.
This could cause the workpiece to be ejected or
cause a dangerous breakage of the wheel.
When the cut-off wheel has worn down considerably,
use a spacer block of sturdy, non-flammable material
behind the workpiece as shown in the figure. You can
more efficiently utilize the worn wheel by using the mid
point on the periphery of the wheel to cut the workpiece.
►
Fig.12: 1.
Spacer block
2.
Handle
Long workpieces must be supported by blocks of
non-flammable material on either side so that it will be
level with the base top.
► Fig.13: 1. Blocks