Make Noise Brains Скачать руководство пользователя страница 10

Страница: 10 / 11

Patch Examples:

Voltage Controlled Pendulum:

With sequence running, patch the Gate Output from Stage 8 (or 4, or ?) to the Trigger Input of MATHS CH. 4. Take EOC Output

from MATHS, patch to BRAINS Direction Input. Set MATHS CH. 4 Rise to 12:00, Fall to 3:00 and Response to Linear. The sequence

should be traveling BWD at this point, but it really depends upon the rate of the incoming clock at BRAIN CLK Input. By setting or

modulating the Fall parameter of CH. 4, you will have control over the direction of the sequence and how long sequence travels

in that direction.

Buchla 250e Style Movement:

Patch MATHS CH. 1 EOR to Clock Input, BRAINS. Set MATHS to Cycle, Rise panel control to Noon, Fall will set upper limit of clock

rate. Sequence should be running. Patch the bottom most row of Tuned Voltages from PRESSURE POINTS, to MATHS CH. 1 Fall

Control Input. Set all potentiometers in corresponding row to Full CCW. Sequence is now running at the upper limit (fastest)

tempo/rate. This Row of pots is like the INNER row of pots on the 250e, each setting their corresponding stage's length. As you

set any stage's pot further CW, the length of that stage increases. The other two rows of pots in the PP/BRAINS system are used

like the OUTER row of pots on the 250e, and at their outputs, you have the Arbitrary Function quantized to the Master Clock.

Содержание Brains











