MAKE A WAKE MARINE ADVANCER TOWER Скачать руководство пользователя страница 10

 

Attach one of the rear legs to your tower. Lift the tower and one person can adjust the position of 
the rear leg backwards, forwards, up, and down to position you like. You stand back and look from 
the side to see what you like the best. 
Mark the deck mount position you like. Take measurements mark out the opposite side of the boat. 
 
WARNING: Before drilling check for objects, wires, etc. under the deck where you are going to drill. 
 
INSTALL BY YOURSELF. 
You might have to do some guess work with the location of the rear mount. As a guide, 1.75m from 
the front and position the mount near the top edge of the deck for the strongest area of the boat. 

STEP 11: Once you have the rear legs on the tower, TIGHTEN all the deck mounts from 
underneath the deck. 

 
Make sure the front knuckle joints are square so you can pivot and lower the tower from the front. 

STEP12: Center and align the tow point to the center of the boat.  
 

NOW you can drill and bolt the top section using the reference marks you made earlier. Have the 
tow point vertical or leaning slightly forwards. 
 

STEP 13: Double check everything is in line and looks correct.  

Now you can go around to every fitting mark across the fitting to the tube. Once you have marked 
all the joints. Remove one fitting at a time, use lock tight on the center bolt and re attach each bolt. 
For the bolt you need to loosen to fold do not use lock tight. 
CARE AND MAINTENANCE 
Be sure to check and tighten all fasteners and connections prior to every use Be cautious when 
towing or driving under obstacles, low hanging structures or trees Leave tower in the erect position 
when towing behind a vehicle Use soap and water to clean your tower. Always rinse and wipe 
down tower after contact with salt (brackish) water. You will have to keep this tower polished to 
keep its nice shine. If Powder coated tower wipe and keep clean do not use abrasive materials or 
liquids to clean. Check before using cleaning agents on tower. 

 

How to fold the tower

 

I.

 

Disconnect tower from rear mounts

 

II.  Loosen the front mounts

 

III. Fold tower back to down position

 

 

 

Содержание ADVANCER TOWER













Отзывы: