●
Battery life (ACA, continuous, no load, with R03)
: approx. 170 hours
●
Dimension, Weight : 204(L)×81(W)×36(D)mm, approx. 220g
(including batteries)
●
Accessories :
Test leads Model 7066A
1set
Battery R03(AAA)
2pcs
Instruction manual
1pce
Carrying case Model 9079
1pce
3. ACA Measurement
●
Disconnect the test leads from the instrument when performing a
test.
●
Do not exceed the rated voltage (600V) and the category ratings
of the instrument.
●
Keep your fingers and hands behind the barrier during
measurement.
DANGER
(1) Set the Function switch to AC A position.
(2) Press the trigger to open the Current Sensor and clamp the
one conductor (Dia. 33mm max.) under test.
Measurement accuracy is guaranteed when the measured object is
placed at the center of the Current Sensor.
NOTE
4. ACV/DCV Measurement
(1) Set the Function switch to AC V or DC V position.
(2) Firmly connect the test leads to V/Ω and COM terminals.
ACV
DCV
If the connection is reversed, the LCD indicates the “
−
“ mark
(DCV measurement).
NOTE
●
Before starting a measurement, ensure that the Function switch is
set to the appropriate position.
●
Do not exceed the rated voltage (600V) and the category ratings
of the instrument.
●
Keep your fingers and hands behind the barrier during
measurement.
DANGER
Power off the circuit under test before making measurements with this
instrument.
WARNING
5. Resistance(Continuity)Measurement
(1) Set the Function switch to resistance or continuity position.
(2) Firmly connect the test leads to V/Ω and COM terminals.
Resistance
Continuity
Beeps less than 90Ω
LCD indicates “OL” when the test leads are open.
NOTE
6. Other Functions
●
Data Hold
Press the Hold key. The LCD shows “ ” mark and the reading
will be held.
Press the Data Hold Key again
to release the display.
●
Low battery indication
The LCD shows “ ” mark when the batteries fall below the
normal operating voltage.
Replace the batteries
with new ones when
this mark appears.
●
Sleep Function
Automatically powers off the instrument in about 10 min after the
last switch or key operation. Buzzer beeps five times one minute
before entering into the Sleep mode, and also one time just
before entering into the mode. To exit from the Sleep mode,
rotate the Function switch or press Hold key.
To disable the Sleep function,
press the HOLD key and
power on the instrument.
Confirm that the LCD shows
“
” about 1 sec.
HOLD
H
BATT
H
BATT
7. Battery Replacement
WARNING
● Do not mix old and new batteries. Brand and type of the batteries
to be used should be harmonized.
● Install batteries in correct polarity as indicated in the Battery
Compartment.
CAUTION
(1) Set the Function Switch to "OFF" position.
(2) Unscrew and remove the Battery Compartment Cover on the
instrument.
(3) Replace the batteries observing correct polarity. Use new two AAA
1.5V batteries.
(4) Install the Battery Compartment Cover and tighten the screw.
● Replace the batteries when a Low Battery Voltage warning " "
mark is indicated on the LCD. Otherwise, precise measurement
cannot be made.
If batteries are completely exhausted, the LCD goes blank without
showing " " mark.
● Do not try to replace the batteries if the surface of the instrument
is wet.
● Disconnect the test leads from the object under test and power
off the instrument before opening the Battery Compartment
Cover for battery replacement.
BATT
BATT
MAJOR TECH
(PTY) LTD
T9 Industrial Village, Sam Green Road,
7
Tunney Ext. 9,
,
Elandsfontein
South Africa
P.O. Box 888, Isando 1600,
South Africa
Telephone: +27 11 8 2
7 5500
National Contact Number: 08 61 62 5678
Sales Facsimile: +27 11 822 2806
Admin Facsimile: +27 11 822 1411
E-mail: [email protected]
www.major-tech.com
