Majestic Ashland Series Скачать руководство пользователя страница 11

Majestic • Ashland ASH36 Installation Manual  • 4059-909 • Rev D • 04/19

11

C. Construct the Chase

A chase is a vertical boxlike structure built to enclose the 

fireplace and/or its vent system. Vertical chimneys that 

run on the outside of a building must be installed inside a 

chase.

In cold climates, Hearth & Home Technologies recom

-

mends that the chase be well insulated using batt type 

insulation between the joists.
Construction of the chase may vary with the type of build

-

ing. These instructions are not substitutes for the require

-

ments of local building codes. Local building codes MUST 

be checked.
Chases should be constructed in the manner of all outside 

walls of the home to prevent cold air drafting problems. 

The chase should not break the outside building envelope 

in any manner. All outer walls need to be insulated.
Building codes require false ceiling and ceiling firestops/

attic shields at each floor of the chase or every 10 ft (3048 

mm) of clear space to control spread of fire.
Walls, ceiling, base plate and cantilever floor at the first 

level of the chase should be insulated (see Figure 3.3.) 

Vapor and air infiltration barriers should be installed in the 

chase as per regional codes for the rest of the home. Ad-

ditionally, Hearth & Home Technologies recommends that 

the inside surfaces be drywalled and taped (or the use of 

an equivalent method) for maximum air tightness.
Holes and other openings should be caulked with high 

temperature caulk or stuffed with unfaced fiber glass 

insulation.

Ceiling 

Firestop 

Metal Chase Top 

Round Termination Cap

False Ceiling 

Insulation in the 

outside walls 

of the chase 

Attic  

Insulation 

Shield 

Chimney 

Ceiling 

Firestop 

Tabs 

False Ceiling 

False Ceiling 

Insulation 

Insulation 

Storm Collar

Figure 3.3  Chase Assembly

All outside walls should be insulated. 

Figure 3.4  Chase Constructions

 

1.  Fireplace and chimney enclosed in an exterior chase.

  2.  Chimney offset through exterior wall and enclosed in chase.

  3.  Chase constructed on roof.

•  The chase is constructed using framing materials much 

the same as the walls in your home. A variety of siding 

materials  may  be  used  including  brick,  stone,  veneer 

brick, or standard siding materials. 

•  In  constructing  the  chase,  several  factors  must  be 

considered:

-

  Maintain  a  2  in.  (51  mm)  air  space  around  the 

chimney.

-  The  chase  top  must  be  constructed  of  non-

combustible material.

-  In cold climates, a firestop spacer and attic insulation 

shield should be installed in an insulated false ceiling 

at  the  8  ft.  (2438  mm)  level  above  the  fireplace 

assembly. This reduces heat loss through the chase.

-  In cold climates, the walls of the chase should be 

insulated to the level of the false ceiling as shown in 

Figure 3.3. This will help reduce heat loss from the 

home around the fireplace.

WARNING! You must install false ceilings and ceil-

ing firestops at each floor of the chase or every 10 ft 

(3.05 m) to control spread of fire.

WARNING! Risk of Fire! DO NOT 

seal area between fire 

stop opening and chimney pipe except where they enter 

the attic or leave the warm air envelope of the home (use 

600° F sealant). 

WARNING! Risk of Fire! 

You must maintain a minimum 

2 in. (51 mm) air space clearance to insulation and oth

-

er materials surrounding the chimney system.

•  Insulation and other materials must be firmly secured to 

prevent accidental contact with chimney system.

•  The chase must be properly blocked to prevent blown 

insulation or other combustibles from entering and 

making contact with fireplace or chimney.

•  Failure to prevent contact between insulation or other 

materials and chimney system may cause overheating 

and fire.

Содержание Ashland Series













































Отзывы: