Majestic ASH36 Скачать руководство пользователя страница 34

Страница: 34 / 44

Majestic • Ashland ASH36 Installation Manual • 4059-909 • Rev D • 04/19

D. Mantel and Wall Projections

The combustible mantel may have a maximum depth of 12

in. (305 mm). Positioned 22 in. (559 mm) above the open

ing. Combustible trim pieces that project no more than 1-

1/2 in. (38 mm) from the face of the fireplace can be placed

no closer than 6 in. (152 mm) from the top of the opening.

7 ft (2134 mm)

minimum

base of fireplace

to ceiling

Combustible Wall

2 x 4 stud wall

Standoffs

Measured from top of fireplace opening

12 in./305 mm

1 1/2 in./38 mm

maximum

Mantel

22 in./559 mm

minimum

Combustible

Decorative Facing

6 in./152 mm

minimum

12 in./305 mm

minimum

Grid represents

1 in. squares

Non-combustible

Decorative Facing

such as:

Steel, iron, brick,

tile, concrete, slate,

glass, plasters.

DO NOT cover any

air openings in the face

of the fireplace.

Seal joint with non-combustible

sealant to prevent heat from being

drawn into the wall cavity.

Figure 7.13 Mantel Specifications

18 1/2 in. [470 mm]

19 3/4 in. [500 mm]

4 in.

[102 mm]

50° angle

39° angle

24 in.

[610 mm]

BRICK

FRONT

FLUSH

FRONT

24 in.

[610 mm]

22 3/8 in. [568 mm]

46 7/8 in. (1191 mm)

36 in.

[914 mm]

Note: Grid depicts 1 inch squares.

Figure 7.14 Mantel Leg, Surround or Wall Projection (acceptable

on both sides of opening)

E. Sidewalls/Surrounds

• Locate adjacent combustible sidewalls a minimum of 24

in. (610 mm) from fireplace opening.

• Mantle leg, surround, stub wall, whether combustible

or non-combustible, may be constructed as shown in

Figure 7.14.

WARNING! Risk of Fire!

• You must seal around the finishing material to fireplace.

Содержание ASH36













































Результаты поиска

Содержание ASH36

Отзывы:

Похожие инструкции для ASH36

Бренды по названию

Популярные бренды

Majestic ASH36, Руководство по установке

Результаты поиска

Содержание ASH36

Отзывы:

Похожие инструкции для ASH36

Бренды по названию

Популярные бренды