background image

42

73D0129

DVKHL Series Gas Fireplace

reMOte cOntrOL OperatIOn

aux control (rear Burner Shut Down)

Figure 56

1.  Press AUX button once to turn rear burner off. AUX shows on the LCD.
2.  Press AUX button again to turn on rear burner. AUX icon disappears.

°F

FP2149
AUX display
12/08

AUX

FP2149

Figure 56 - 
AUX Display

Low Battery Detection

Figure 57

1.  Battery voltage is checked once a minute. When the battery voltage drops to a certain 

level, the low-battery icon will display on LCD, and the transmitter will turn off the fireplace. 
The transmitter will not function anymore until fresh batteries are installed.

2.  When  the  batteries  are  low,  the  LCD  displays  a  low  battery  indicator. The  low  battery 

indicator will be displayed in any mode.

3.  The transmitter will not operate with low batteries. Change the batteries before the batter-

ies are too weak for normal operation. Turn the unit OFF before replacing batteries.

°F

FP2150
low battery display
12/08

FP2150

Figure 57 - 
Low Battery Display

child-proof protection

Figure 58

1.  Press and hold the ON and OFF buttons simultaneously for three (3) seconds to enter 

child proof mode. Figure K

2.  The transmitter will not send a signal again until the childproof mode is deactivated by 

pressing the ON and OFF buttons simultaneously for three (3) seconds to exit child proof 
mode and the Childproof indicator disappears from LCD.

°F

FP2151
no child display
12/08

FP2151

Figure 58 -
Child Protection Display

transmitter thermal Shutdown

Figure 59

1.  If transmitter measures a room temperature exceeding 99° F, the LCD will display "HI" 

and the transmitter will turn off the fireplace.

2.  Transmitter  will  not  function  until  the  room  temperature  has  dropped  below  99°  F.  If 

transmitter measures a room temperature less than 40° F, the LCD will display "LO" and 
NO SIGNAL will be sent to turn on the fireplace.

FP2152
thermal shutdown display
12/08

FP2152

Figure 59 -
Thermal Shutdown Display

Содержание 500DVKHL

































































Отзывы: