background image

DVB Series Direct Vent Gas Fireplace

34

54D0701

1. 

stop!

 Read the safety information above.

.  Make sure all power to unit is turned off. 
3.  Set thermostat to lowest setting.
4.  This  appliance  is  equipped  with  an  ignition  device  which 

automatically lights the burner. Do not try to light the burner 
by hand. 

5.  Turn on all electric power to appliance.
6.  Set thermostat to desired setting.
7.  Turn RS-OFF-ON rocker switch to “ON”. 
8.  If the appliance will not operate, follow the instruction 

To Turn Off Gas 

below

 

and 

call your service technician or gas supplier. 

A. 

This  appliance  is  equipped  with  an  ignition  device 
(Piezo) which automatically lights the pilot. Do NOT 
try to light the burner by hand. 

B. 

BEFORE  OPERATING  smell  all  around  the  appli-
ance area for gas. Be sure to smell next to the floor 
because some gas is heavier than air and will settle 
on the floor.

WhAt to Do IF you sMell GAs:

 

•  Turn off all gas to the appliance.

 

•  Open windows. 

 

•  Do not attempt to light any appliance.

 

•  Do not touch any electric switch; do not use any phone in your building.

 

•  Immediately call your gas supplier from a neighbor's phone. Follow the gas 

supplier's instructions.

 

•  If you cannot reach your gas supplier, call the fire department.

c.  

Turn off all electric power to appliance. 

D.

  Do not use this appliance if any part of it has been under water. Immediately call 

a qualified service technician to inspect the appliance and to replace any part of 
the control system and any gas control that has been under water. 

opeRAtING INstRuctIoNs (electRoNIc)

LO

HI

FP2102
BDV electronic valve

Figure 50 - 
Electronic Gas Valve 

  lIGhtING electRoNIc IGNItIoN   

 FoR youR sAFety ReAD BeFoRe lIGhtING 

  to tuRN oFF GAs   

Never use an open flame 
to check for gas leak. 

WARNING

1.  Open lower door.
.  Turn RS-OFF_ON rocker switch to “OFF”.
3.  Turn off all electric power to the appliance if service is to be performed.
4.  Close lower door. 

W

ARNING

If  you  do  not  follow  these 
instructions  exactly,  a  fire  or 
explosion  may  result  causing 
property  damage,  personal 
injury or loss of life.

Содержание 300DVB

































































Отзывы: