background image

6

NVC Series B-Vent 

20000194

Clearance to Combustibles

Appliances

 

Top .......................................................... 0” (0 mm)

 

Bottom ..................................................... 0” (0 mm)

 

Side ......................................................... 0” (0 mm)

 

Back ........................................................ 0” (0 mm)

 

Perpendicular Sidewall ........................... 0” (0 mm)

 

Top of unit to ceiling .......................... 36” (914 mm)

 

Front of unit to combustibles ............. 36” (914 mm)

Venting

 

B-Vent ................................................... 1” (25 mm)

Mantels

The height that a combustible mantel is fitted above the 
fireplace is dependent on the depth of the mantel. This 
also applies to the distance between the mantel leg (if 
fitted) and the fireplace.
For the correct mounting height and widths refer to 
Figures 2a and 2b and the Mantel Chart below.
The distances and reference points are not affected by 
the fitting of a bay window front trim kit. 
Noncombustible mantels and legs may be  installed at 
any height and width around the appliance.
When using a paint or lacquer to finish the mantel, 
such paint or lacquer must be heat resistant to prevent 
discoloration.

A B C D E

V

W

X

Y

Z

Fireplace

CFM146

DV Mantel Chart

7/5/01   sta

 

Ref. 

Mantel   

Ref. 

Mantel From Top 

 

 

 Shelf Depth 

 

of Comb. Chamber

 

10"  (254 mm) 

19

¹⁄₂

"  (495 mm)

 

8"  (203 mm) 

17

¹⁄₂

"  (444 mm)

 

X  

6"  (152 mm) 

15

¹⁄₂

"  (394 mm)

 

4"  (101 mm) 

13

¹⁄₂

"  (343 mm)

 

2" ( 51 mm) 

11

¹⁄₂

"  (292 mm)

Fig. 2a

  Mantel clearances.

Side View

CFM146

Top of 

Combustion Chamber

Bottom of Door Trim

Top Louvre Assembly

J

F

G

H

I

Mantel

Leg

CFM164a

Mantel Leg Chart

06/22/01   sta

  Ref. 

Mantel   

Ref.  Mantel Leg From Side 

 

 

 Leg Depth 

 

of Comb. Opening

 

10"  (254 mm) 

12"  (305 mm)

  G 

8"  (203 mm) 

10"  (254 mm)

  H  

6"  (152 mm) 

8"  (203 mm)

 

4"  (101 mm) 

6"  (152 mm)

 

2" ( 51 mm) 

4"  (101 mm)

CFM170

DV Builder Front 

View

O

N

M

L

K

CFM164

CFM170

Fig. 2b

  Combustible mantel leg minimum installation.

Side of 

Combustion Chamber

Black 

Surround 

Face

Hearth

A hearth is not mandatory but is recommended for 
aesthetic purposes. We recommend a noncombustible 
hearth. 

Cold climate installation recommendation: When 

installing this unit against a noninsulated 
exterior wall or chase, it is mandatory that 
the outer walls be insulated to conform to 
applicable insulation codes.

Содержание NVC36





























Отзывы: