Majestic fireplaces 360DVS2 RN Скачать руководство пользователя

Страница: 24 / 44

360 DVS Series Direct Vent Fireplaces

10006326

Operating Instructions

Only glass approved by CFM Corporation

should be used on this ﬁreplace.

Glass Information

• The top side and top end

louvres are removed by simply
lifting the louvre assembly and
pulling the assembly away
from the ﬁreplace. (Fig. 36)

• The lower side louvres are

hinged along there lower
edge and are folded down for
access to components in the
base cavity of the ﬁreplace.

• The lower end louvre assembly

on the 360DVS3/ SL/ SR units
is removed in the same man-
ner as the top louvre assem-
blies.

Louvre Removal

FP1227

Louvre removal

11/02

Louvre

Glass Panel

FP1227

Figure 36

Window Frame Assembly Removal

Side Window Frame Assemblies

1.  Shut off the gas supply.
2.  Allow the ﬁreplace to cool if it has been in operation.
3.  Remove the top louvre assembly.
4.  Lower the bottom louvre assembly.
5.  Release the two clamps along lower edge of the

frame by pulling down on clamp handles. (Fig. 37)

6. Tilt lower edge of frame out slightly and lift window

frame assembly up and away from the ﬁreplace.

7. To reinstall the window frame assembly reverse

this procedure.

Front Window Frame Assembly

1. Remove the top and bottom louvre assembly.
2. Remove the lower window trim (held in place with

magnets).

3. Remove both lower retaining screws. Access to

these screws is gained through the holes along the
lower edge of the frame behind the trim. (Fig. 38)

4. Tilt lower edge of frame out slightly and lift window

frame assembly up and away from the ﬁreplace.

5. To reinstall the window frame assembly reverse

the process.

FP1228

remove glass frame

11/02

Window

Frame

Assembly

Lower Clamps

Window

Frame

Assembly

Pull Clamp

Hook

Push

Clamp

Han-

dle

FP1228

Fig. 37

Window frame assembly removal.

Remove_end_glass&frame

360DVS

rev. -9-17-02 rjs

Location of Lower

Retaining Screws

FP1445

Fig. 38

Retaining screw.

•

The use of any non-approved replacement glass will

void all product warranties.

•

Care must be taken to avoid breakage of the glass.

•

Do not operate appliance with glass front

removed, cracked or broken.

•

Replacement glass (complete with gasket) is

available through your Majestic Fireplaces

dealer and should only be installed by a licensed

qualiﬁed service person.

��

�

��

Содержание 360DVS2 RN













































Результаты поиска

Содержание 360DVS2 RN

Отзывы:

Похожие инструкции для 360DVS2 RN

Бренды по названию

Популярные бренды

Majestic fireplaces 360DVS2 RN, Руководство по установке и эксплуатации для владельцев жилья

Результаты поиска

Содержание 360DVS2 RN

Отзывы:

Похожие инструкции для 360DVS2 RN

Бренды по названию

Популярные бренды