Maico ERO SCAN Скачать руководство пользователя | Manualshive

Страница: 10 / 74

background image

Operation Manual

ERO•SCAN

®

1

8106556 Rev. 11

8

13//08/2020

2.2 Customer Responsibility

All safety precautions given in this operation manual must  be observed at all times.
Failure  to  observe  these  precautions  could  result  in  damage  to  the  equipment  and
injury to the operator or subject.

The employer should instruct each employee in the recognition and avoidance of
unsafe conditions and the regulations applicable to his or her work environment to
control or eliminate any hazards or other exposure to illness or injury.

It is understood that safety rules within individual organizations vary. If a conflict exists
between the material contained in this manual and the rules of the organization using
this device, the more stringent rules should take precedence.

This  product  and  its  components  will  perform  reliably  only
when  operated  and  maintained  in  accordance  with  the
instructions contained in this manual, accompanying labels,
and/or inserts. A defective product should not be used. Make
sure  all  connections  to  external  accessories  are  snug  and
secured properly. Parts which may be broken or missing or
are  visibly  worn,  distorted,  or  contaminated  should  be
replaced immediately with clean, genuine replacement parts
manufactured by or available from MAICO.

NOTE:

Customer responsibility includes proper maintenance and cleaning of the device.

Section 3.2

Section 3.3

Cleaning and Disinfection Recommendations

Breach of the customer

responsibility can lead to limitations of Manufacturer’s

Liability and Warranty.

Section 2.3

Manufacturer’s Liability

Section 3.1

NOTE:

In the unlikely case of a serious incident, inform MAICO as well as the

competent authority of the Member State in which the user and/or the patient is
established.

2.3

Manufacturer’s Liability

Usage of the device in a way deviant from the intended use will lead to a limitation or
termination of the manufacturer’s liability in case of damage. Improper use includes
disregarding the operation manual, the operation of the device by underqualified
personnel as well as making unauthorized alterations on the device.

WARNING

«
...
8
9
10
11
12
...
»

Содержание ERO SCAN











































































Отзывы:

Нет отзывов

Похожие инструкции для ERO SCAN

Бренд: Kapriol Страницы: 32

Бренд: Landoll Страницы: 34

Бренд: UNIA Страницы: 62

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: IBEX Страницы: 4

Бренд: Fast Страницы: 60

Бренд: Rainbow Colour Changers Страницы: 22

Бренд: Protech Machinery Страницы: 21

Бренд: TOORX Страницы: 28

Бренд: KaVo Страницы: 70

Бренд: GreenTec Страницы: 66

Бренд: Slick Страницы: 2

Бренд: Cattani Страницы: 99

CLAMP ON LEAK HiTESTER 3283

Бренд: Hioki Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды