Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 98

Страница: 98 / 115

FUEL SAVING TIPS

To save fuel & oil in your tractor, following things should always be kept in mind.

A) Air cleaning system

1) Clean the air cleaner regularly so that dust does not settle down.
2) For every 50 hours & everyday in sandy/dusty conditions.

(a) Clean the air cleaner filter element with compressed air.
(b) If the rubber ring is cut or expanded then change it with an appropriate one.

Fix the rubber at the proper location & check for leakages if any.

Note: If air cleaning system is not properly maintained, it will lead to early wear of piston rings

& sleeves. This will lead to problems like loss of engine power,, excessive oil consumption
fuel consumption.

B) Engine

1) put the engine oil on load after the engine is heated & the water temperature gauge indicates

the needle to be in the green zone.

2) If excessive black smoke is visible, then the paper element of air cleaner, Fuel injection

Pump or nozzles should be checked.

3) Do not run the engine without load for more than 2 minutes. It is better to stop the engine

rather than run it idle. This will help in saving of fuel.

C) Clutch & Brakes.

1) Do not reduce the power of the power of the engine by depressing the clutch halfway. Instead

use low gear.

2) If the Tractor has to be stopped for a long period, it is advisable to bring the transmission in

neutral position & release the clutch pedal.

3) Do not over ride the clutch & brake pedals.
4) While coming down from a slope, reduce the engine throttle & use low gear. Do not depend

only on the brakes for stoppage.

D) Fuel system

1) Always use filtered diesel for the fuel system
2) At the end of the day’s working, it is preferable to fill the diesel tank so that it may prevent

condensation.

3) Change the filter, if the system gets choked. Do not change both the filters at the same time.

If the above directives are not adhered to, the fuel injection pump & injection nozzle will lose
its life early. Also, it will lead to excessive black smoke & excessive diesel consumption.

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды