background image

5 - Operation and MaintenanceOperation and Maintenance 

DynaFlex II| Smart Card Reader | PCI PTS POI v6.2 Security Policy 

 

Page 12 of 17 (

D998200573-10

5

 

Operation and Maintenance 

5.1

 

Periodic Inspection 

The merchant or end user, should inspect the appearance of secure card reader on a daily basis, paying 
close attention to the following: 
1)

 

Inspect the appearance of secure card reader to make sure it is the right product. 

2)

 

Inspect whether the Swipe Path has an additional card reader or other inserted bugs, See 

Figure 5-1

below.  

3)

 

Observe the Chip Card Insertion Slot to determine whether there are any wires or obstructions. See 

Figure 5-1,

 below.  

4)

 

Inspect whether the product appearance has been altered. 

5)

 

Check if the firmware version is correct. 

6)

 

Power on the secure card reader and check that the firmware runs well, as the startup will inspect the 
hardware security, authenticity, and integrity of firmware. Only the leftmost LED should be on and 
blinking green. 
 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
MagTek strongly recommends performing security inspections on a regular schedule.  Additional 
information can be found in 

D998200563 DYNAFLEX II DEVICE INSPECTION

 or 

D998200566 

DYNAFLEX II KIOSK DEVICE INSPECTION

.  If any problems are detected, stop using the device, 

set it aside in a secure location, and contact the manufacturer or your acquirer for further advice.

Chip Card Insertion Slot 

The card slot for the Contact Chip Reader is a 
smooth, unobstructed path. Other than the 
contact points that read the chip, there are no 
electronics, mechanics, or wires in the path.  

Swipe Path 

The swipe path is smooth. The only moving part 
is the spring-mounted read head that depresses 

into the device as the card’s magnetic stripe 

contacts the read head.   

Figure 5-1 - Chip Card Insertion Slot and Swipe Path Examples 

Содержание DynaFlex II


















Отзывы: