Magnum Winchester WINACP Скачать руководство пользователя страница 7

 

7

9

 

There are many varieties of corn grown around the world.  Each variety has unique characteristics 
including the shape and size of the kernel.  Your stove will burn more consistently with a small to 
mid-size kernel corn.  If the kernel size of the corn varies greatly or if you switch sources frequently, 
you will get a less consistent burn, which will require more attention to the draft setting on your stove.  
Therefore, purchasing corn from the same source will help achieve a more consistent burn.  

DO NOT 

USE CORN WITH A HIGH WAX CONTENT! 

 

WOOD PELLETS 

 

9

 

Be consistent in your wood pellet fuel supplier.  Wood pellets will vary in content and burn 
characteristics from supplier to supplier.  A consistent supply of wood pellets will require fewer 
adjustments to the draft of the stove. 

 

9

 

Check your wood pellets for foreign objects.  Your stove warranty will not cover damage done to your 
stove due to foreign objects in the fuel supply. 

 

9

 

Store your wood pellets in a dry place to prevent them from absorbing excess moisture. 

 

9

 

Vacuum the hopper out after every 6-7 bags to eliminate buildup of sawdust.  More often if the wood 
pellets are poor quality.  If sawdust is a problem you will have to screen each bag of fuel for a 
consistent feed. 

 

9

 

Wood pellets vary from supplier to supplier in ash content from less than 1% to 3% or more.  Low ash 
content pellets will allow you to burn the stove longer between cleanings.  Only wood pellets 
manufactured to the Association of Pellet Fuel Industries (A.P.F.I.) standard for residential pellet fuels 
are recommended.  Look for A.P.F.I. registration number on the back of pellets.  Consult your local 

MagnuM 

reseller for more information on approved wood pellet fuel. 

 

9

 

It is strongly recommended not to keep a supply of wood pellets over the summer months.  Moisture 
will build up and cause problems in the fall with your appliance operation.  Make sure that your 
supplier is not selling you left over fuel or fuel that has been out in the rain. 

 
 
 
 

When you receive your MagnuM Corn/Biomass/Wood Pellet Stove

, Pedestal unit, Leg unit or 

Fireplace Insert

, be careful to inspect all parts and components to make sure that nothing was 

damaged or lost in shipment.  If there was shipping damage, be sure to report it to your MagnuM 
reseller, or the shipping company that delivered your unit.  

Freight damage claims must be made to 

UNPACKING YOUR MAGNUM CORN/BIOMASS/WOOD PELLET UNIT

 

the Freight Company immediately.

  If parts are missing contact your local MagnuM reseller or 

contact the factory right away.  

Your satisfaction is our top priority

 
To uncrate your 

MagnuM appliance

 

1)

 

Cut the banding straps and open the carton lid. The carton is stapled to the wood pallet so it will be 
necessary to pull the cardboard loose from the pallet. Remove the crating box carefully lifting up over 
the top of the unit. Be careful not to scratch the unit with the staples. Remove the wood blocks and 
plastic. We strongly urge you to recycle the packaging materials to help protect the environment. 
 

Содержание Winchester WINACP




















































Отзывы: