Magnum MS2000 Скачать руководство пользователя страница 14

Страница: 14 / 82

Page 4

Introduction

Figure 1-2, Electrical Connection Points

Positive (+)

DC Terminal

(under cover)

Negative (-)

DC Terminal

(under cover)

Mounting

Flange

Equipment

Ground

Terminal

AC Entry/

Exit

Connections

Intake Air Vents

(and on right front side)

DC Equipment Ground Terminal

– this connection is used to tie the exposed chassis

of the inverter to the DC grounding system. This terminal accepts CU/AL conductors from

#14 to #2 AWG (2.1 to 33.6 mm2). Tightening torque is 45 in-lb.

AC Entry/Exit Connections

– two 3/4” knockouts provided with cable-clamp strain

reliefs to accommodate and secure the AC input and output

eld wiring.

Intake Air Vents

– ventilation openings to pull in air to help keep the inverter cool for

peak performance.

Positive DC Terminal

– provides a 360 degree connection point for the positive (+) cable

from the battery bank; consists of a 5/16-18 bolt with a Kep or Flange nut that holds the

battery cable to the DC terminal.

Negative DC Terminal

– provides a 360 degree connection point for the negative (–)

cable from the battery bank; consists of a 5/16-18 bolt with a Kep or Flange nut that

holds the battery cable to the DC terminal.

Mounting Flange

– used to secure the inverter to a shelf or wall.

Содержание MS2000



















































































Результаты поиска

Содержание MS2000

Отзывы:

Бренды по названию

Популярные бренды

Magnum MS2000, Руководство пользователя

Результаты поиска

Содержание MS2000

Отзывы:

Бренды по названию

Популярные бренды