manualshive.com logo in svg

Magnum MMG 125, Руководство по эксплуатации, Страница: 8 / 48

Поделиться
Скачать
Magnum MMG 125 Скачать руководство пользователя страница 8

SAFETY SYMBOL SUMMARY

This equipment has been supplied with numerous safety and operating decals.  These decals provide important
operating instructions and warn of dangers and hazards.  Replace any missing or hard-to-read decals and use
care when washing or cleaning the unit.  Below is a summary of the intended meanings for the symbols used on
the decals.

8

Hot surface(s) nearby.

Fire/explosion hazard; Keep 
open flames away from unit.

Read and understand the 
supplied operator’s manual 
before operating unit.

Remove negative battery 
cable before performing 
any service on unit.

Stop engine before making 
connections.

Use clean diesel fuel only.

Unit electrical ground.

Hearing protection required
while operating unit with doors 
open.

Anchor/tie down point.

Lift here only.

Asphyxiation hazard; Operate 
in well ventilated area.

Dangerous voltage may be
present.

Never change switch position 
while engine is running.

Burn/scald hazard; 
pressurized steam.

Fan hazard; Keep body parts 
clear of this area.

Isolate generator to prevent 
electrocution hazard.

Belt/entanglement hazard; Keep 
body parts clear of this area.

Safety alert symbol;  Used to 
alert you to potential personal 
injury hazards.  

Stop engine before fueling.

Engine running.

Содержание MMG 125

















































Отзывы:

Нет отзывов