Magnum MI-16150 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 15

Magnum MI-16150 Скачать руководство пользователя страница 6

TILTING THE TABLE

1. Loosen the two table lock knobs (A), located under the table at both sides of the machine

2. Tilt the table forward to the desired angle with your hands.
3. An angle scale is provided at the right side of the trunnion to indicate the degree of table tilt.
4. Tighten the two table lock knobs securely after the table degree has been adjusted.

1. The verticality between the table and drum has been adjusted by factory before shipment.
However, after a long period of operation, the verticality may become inaccurate.

2. To adjust the verticality, set the table to a flat horizontal position. The table tilting scale should read
zero degrees.

3. Place a 90° combinative square on the table and against the drum.
4. If the table is not 90° from the drum, adjust the angle of the table by changing the height of the
resting post as shown.

5. If the table is 90° from the drum, but the scale does not read zero degree, set the scale to read
zero degree by loosening the screw on the angle indicator and setting the arrow to zero.

ADJUST THE VERTICALITY BETWEEN THE TABLE AND DRUM

05

«
...
4
5
6
7
8
...
»

Содержание MI-16150
















Отзывы:

Нет отзывов