Magnum Industrial MI-12250, Руководство по эксплуатации

Страница: 2 / 33

IMPORTANT SAFETY RULES
Wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are
certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen
the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the
operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing
protection can reduce your potential for injury. But even the best guard won't make up for poor judgment, carelessness or
inattention, Always use common sense and exercise caution in the workshop. If a procedure feels dangerous, don't try it. Figure
out an alternative procedure that feels safer. REMENBER: Your personal safety is your responsibility.
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY
1. FOR YOUR OWN SAFETY, READ INTRUCTION MANUAL BEFORE OPERATING THE TOOL. Learn the tool's application and
limitation s as well as the specific hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION.
4. GROUND ALL TOOLS. If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical receptacle. If
an adapter is used to accommodate a two-prong receptacle, the adapter plug must be attached a known ground. Never
remove the third prong.
5. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed
from tool before turning it "ON".
6. KEEP WORK AREA AND CLEAN. Cluttered areas and benches invite accidents.
7. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet location, or expose them to rain. Keep
work area well light.
8. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.
9. MAKE WORKSHOP CHILDPROOF - with padlocks, master switches, or by removing starter keys.
10. DON'T FORCE TOOL. It will do the job better and be safer at the rate for which it was designed.
11. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed.
12. WEAR PROPER APPAREAL. No loose clothing, gloves, neck-ties, rings, bracelets, or other jewelry to get caught in moving
parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
13. ALWAYS USE SAFETY CLASSES. Wear safety glasses. Everyday eyeglasses only have impact resistant lenses; they are not
safety glasses. Also use face or dust mask if cutting operation is dusty.
14. SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and frees both hands to
operate tool.
15. DON'T OVERREACH. Keep proper footing and balance at all times.
16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for
lubricating and changing accessories.
17. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits cutters, etc.
18. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by us may cause hazards or
risk of injury to persons.
19. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in “OFF” position before plugging in power cord.
20. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.
21. CHECK DAMAGED PARTS. Before further use of tool, a guard or other part that is damaged should be carefully checked to
ensure that it will operate properly and perform its intended function - check for alignment of moving parts, binging of
moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
22. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of the blade or cutter only.
23. NEVER LEAVE TOOL RUNNING UNATTENDED TURN POWER OFF. Don't leave tool until it comes to a complete stop.
24. DRUGS, ALCHHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol or any medication.
25. MAKE SURE TOOL IS DISCONNECTED FROM POWER SUPPLY while motor is being mounted, connected or reconnected.
26. WARNING: The dust generated by certain woods and wood products can be injurious to your health. Always operate
machinery in well-ventilated areas and provide for proper dust removal. Use wood dust collection systems whenever possible.