Magnetic mTripod страница 71 Скачать руководство пользователя

Страница: 71 / 92

Control unit MGC mTripod

Corrective action

IMPORTANT!
With some messages, the control unit tries to reset the cause of

the message. If the attempt was successful, the message is

displayed as WARNING. If the attempt failed, the message is

displayed as ERROR.

8.4

Displaying and signalling messages

Messages are displayed and signalled as follows:

›

Status display in the MGC.Connect programme:

Page 25, Fig. 7.

›

On the display of the MGC control unit.

›

The output with the function "| Error" is deactivated in case of an error

(ERROR) (closed-circuit principle). This function is not parameterised ex

works.

Page 13, chapter 2.2.

›

The output with the function "| Warning" is deactivated in case of a

warning (WARNING) (closed-circuit principle). This function is not

parameterised ex works.

Page 13, chapter 2.2.

Содержание mTripod





























































































Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Magnetic mTripod, Руководство пользователя

Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды