manualshive.com logo in svg

Magnetic mTripod, Руководство пользователя

Магнитный мТрипод - компактный и удобный тренога для смартфонов с магнитным креплением. Легко устанавливается и удобно переносится. Бесплатно загрузите инструкцию по эксплуатации на manualshive.com, чтобы максимально эффективно использовать этот продукт.

Поделиться
Скачать
background image

25

Control unit MGC mTripod

Description of the "MGC.Connect" programme

Fig. 7: 

Examples of event displays

1  Example of an event of the type WARNING
2  Confirm pending messages and update display
3  Example of an event of the type ERROR

Information on WARNING and ERROR: 

ä

 Page 73, chapter 8.6.

Symbol

Description

OK
No warning and no error is pending.
WARNING
A warning is pending. If you click the "Refresh / Acknowledge" 

button, the warning is confirmed and the display is refreshed.
ERROR
There is an error. After correcting the fault and a reset, you can 

acknowledge the fault and refresh the display via the "Refresh / 

Acknowledge" button. If several errors are pending at the same 

time, the next error is displayed after refreshing.
In the "Service" tab, you can generate a current system report for 

the pedestrian gate. The system report contains an event log with 

additional information about a fault / message such as "Node 

name". 

ä

 Page 30, chapter 4.6.

The pedestrian gate has detected an attempted vandalism.

Содержание mTripod





























































































Отзывы:

Нет отзывов

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Загрузить еще бренды