background image

 

Enrange MLTX2 Intrinsically Safe 

Transmitter Instruction Manual 

April 2019 

Page 10 of 44 

Keep the battery pack environment cool during storage (i.e., not in direct sunlight or close to a heating source). 
 

2.7 

BATTERY DISPOSAL 

 

Before disposing of batteries consult local and governmental regulatory requirements for proper disposal procedure.  
 

2.8 

CRANE/LIFTING DEVICE SPECIFIC WARNINGS 

 

  WARNING 

ALL EQUIPMENT MUST HAVE A MAINLINE CONTACTOR INSTALLED AND ALL TRACKED CRANES, HOISTS, 
LIFTING DEVICES AND SIMILAR EQUIPMENT MUST HAVE A BRAKE INSTALLED.  FAILURE TO FOLLOW THIS 
WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT. 

AN AUDIBLE AND/OR VISUAL WARNING MEANS MUST BE PROVIDED ON ALL REMOTE CONTROLLED 
EQUIPMENT AS REQUIRED BY CODE, REGULATION, OR INDUSTRY STANDARD.  THESE AUDIBLE AND/OR 
VISUAL WARNING DEVICES MUST MEET ALL GOVERNMENTAL REQUIREMENTS.  FAILURE TO FOLLOW 
THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT. 

THE DIRECT OUTPUTS OF THIS PRODUCT ARE NOT DESIGNED TO INTERFACE DIRECTLY TO TWO STATE 
SAFETY CRITICAL MAINTAINED FUNCTIONS, I.E., MAGNETS, VACUUM LIFTS, PUMPS, EMERGENCY 
EQUIPMENT, ETC.  A MECHANICALLY LOCKING INTERMEDIATE RELAY SYSTEM WITH SEPARATE POWER 
CONSIDERATIONS MUST BE PROVIDED.  FAILURE TO FOLLOW THIS WARNING COULD RESULT IN 
SERIOUS INJURY OR DEATH OR DAMAGE TO EQUIPMENT. 

 

Cranes, hoists, lifting devices and other material handling equipment can be large, and operate at high speeds. 
 
The operator should: 

 

continuously watch and monitor status of lifted loads 

 

know and follow cable and hook inspection procedures 

 
The operator shall not:  

 

lift or move more than the rated load 

 

use the crane, hoist or lifting device to lift, support or transport people  

 

lift or carry any loads over people 

 

operate the crane, hoist or lifting device unless all persons, including the operator, are and remain clear of 
the supported load and any potential pinch points 

 

operate a crane, hoist or lifting device when the device is not centered over the load 

 

operate a crane, hoist or lifting device if the chain or wire rope is not seated properly in the sprockets, drum 
or sheave 

 

leave any load unattended while lifted 

 
 
 
 
 
 
 
 
 
 

Содержание Telemotive MLTX2













































Отзывы: