MAINTENANCE
Stainless steel contrary to popular belief can rust. Most commonly, deposits on surface of the product will trap moisture.
It is this moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel to form a
protective layer of chrome oxide. Robbed of oxygen, this reaction does not take place and “crevice corrosion” or “surface
rusting” occurs. To minimize this effect, thoroughly clean your grill with soap and water, rinse with fresh water, and dry.
Avoid using stainless steel polishes on grill exterior as most leave a residue that may discolor when grill is heated.
Additionally, stainless steel that is exposed to high heat will change color and texture over time. The “amber” color of
grill exterior and internal components is not a failure of the stainless steel and will not affect products operation. When this
happens, we recommend using
“Magma Magic” Grill Restorer
to remove the “amber” color and return grill to its original
luster. However, prolonged exposure to extreme high heat will cause chromium and nickel to “burn out” of stainless steel. At
this point stainless steel will become more susceptible to corrosion and will start to deteriorate. We recommended
replacement of internal components as they become seriously deteriorated.
We recommend thoroughly cleaning grill and internal components after each outing. Disassemble interior components
and remove all food residue. Use a “Scotch-Brite” pad or similar product and “Easy-Off” oven cleaner for cleaning grills
interior components, followed by thoroughly washing with soap and water, rinse with fresh water & dry. Thoroughly rinse
the area between the interior heat shield and the front surface of the grill. AVOID CONTACT OF OVEN CLEANER WITH SKIN,
CONTROL VALVE, AND BOAT SURFACE.
CAUTION:
DO NOT USE ANY TYPE OF ABRASIVE PAD ON EXTERIOR MIRROR
FINISH AS IT WILL SCRATCH SURFACE, USE ONLY A SOFT CLOTH. We recommend covering grill between uses. Grill covers
are available at Magma retailers or directly from Magma. See our website,
MagmaProducts.com.
Grill Grates
-
Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for burnt-on residue. Wash with
soapy water and dry prior to storage.
Control Valve
-
All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in any way.
Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris obstructing the orifice.
Repair/Replacement Parts -
All replacement parts are readily available at your Magma Retailers or directly from Magma.
For a complete list of replacement parts visit our website
MagmaProducts.com.
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS
Align valve stem key
to valve chamber
lock detent and rotate
Gas Grill
Propane (LPG)
Gas Regulator
A10-225
Hose Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Gas Grill
Type 3
Valve
Type 3
Valve
Solenoid
Gas Grill
Typical Marine &
R.V. Application
Align valve stem key
to valve chamber
lock detent and rotate
Gas Grill
Propane (LPG)
Gas Regulator
A10-225
Hose Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Gas Grill
Type 3
Valve
Type 3
Valve
Solenoid
Gas Grill
Typical Marine &
R.V. Application
• Magma on-board LPG (propane)
valves and hose kit allow Magma
grills to be installed to an existing
on-board, pre-regulated low
pressure LPG (propane) system.
• Use only
Magma Type 3 Low Pressure
LPG (Propane) Control Valves.
Visit
our website at
MagmaProducts.com
to
view valve application guide.
• North America use
Magma A10-225
LPG Hose Kit
in conjunction with
Type
3 Valve.
Outside North America see your
local dealer for proper hose and fittings.
• Primary shutoff valve
(supplied with
A10-225 hose kit)
must be used at
point of connection to allow shutoff of
gas supply leading to grill.
Install valve as shown in diagram above. Even
though valve may seem loose or not snug-fitting
it will function properly and is safe for use.
6
