madur electronics maMoS 100 страница 79 Скачать руководство пользователя

Страница: 79 / 96

www.madur.com

Manual

maMoS

100/200/300/400

7.3.8. Work cycles

The function is available using the quick access button or via the menu bar

by pressing the "Work mode

button. If the function is called, the window shown in Picture

90. appears. The window enables the user to check the monitor's work stage, set the new

work cycle, prepare the work schedule or set the restarting of the cycle with the help of the

digital inputs. The "Work mode

window is divided into five sections (frames) – each refer-

ring to particular working settings. To view the current mode or to swith into settings ad-

justment use the button

“Look at the analyser”

“Abandon preview”.

Picture 90.

The "Work mode

" window

– setting for the Cyclic measurements.

7.3.8.1. Work mode

This section allows to select the work mode the analyser is using. Depending on

the chosen work mode, the contents of the work mode window changes and shows appro-

priate information. Work modes available to choose from:

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

Похожие инструкции для maMoS 100

Бренды по названию

Популярные бренды

madur electronics maMoS 100, Руководство пользователя

Результаты поиска

Содержание maMoS 100

Отзывы:

Похожие инструкции для maMoS 100

Бренды по названию

Популярные бренды