Cooling
Flavor
Sleeve temperature
The guide values are based on a scale of 5. Your experience might differ.
DIRECT AIRFLOW OPTIONS
(OPTIONAL)
You can expand the capabilities of your Revolve Stem even further with the
optional Direct Airflow Tube. It will remove the DRC options entirely to give
you improved flavor and cooler Sleeve temperature, but with warmer vapor.
(DIRECT) OPEN
Air intake at the Airport is directed to the Mouthpiece for a blast of fresh air
while the vapor heads through the center.
(DIRECT) BYPASS
Fresh air is drawn around the Helix to cool the Sleeve and the Cooling Unit
before mixing with the vapor which then travels through the center.
(DIRECT) CLOSED
The Airport is closed for a hotter, more direct vapor experience.
ADJUSTABLE AIRPORT
When using the OPEN or BYPASS mode you can control the maximum air intake
at the Adjustment Ring with the help of our fully adjustable Airport.
2.5
4
3.5
2
4.5
2
1
5
3.5
DRC AIRFLOW OPTIONS
Align the line on the Adjustment Ring to the Airport to choose from the
following options with the Draw Resistance Control (DRC) Airflow Tube:
OPEN
Fresh air is drawn into the Airport and through the center of the Cooling Unit
before mixing with the vapor and passing over the Helix.
BYPASS
The air intake at the Airport is directed straight to the Mouthpiece for a blast of
cool air that bypasses the Helix.
CLOSED
The Airport is closed. Not adding any fresh air will produce denser clouds while
still cooling the vapor. Perfect for mouth-to-lung use.
4
3.5
3.5
4.5
3.5
5
3
4
5
LOCKABLE SPINNING MOUTHPIECE
The Revolve is a breeze to use with a lighter thanks to its built in
smooth-spinning Mouthpiece. If you are using a heater or just want to fix the
Mouthpiece you can lock or unlock the mechanism with a quick adjustment.
LOCKED MODE
Pull out the Airflow Tube from the Mouthpiece and roll the o-ring from its
storage position into the locking groove as shown above. The o-ring will create
friction on the inner side of the Mouthpiece which will stop it from spinning.
SPINNING MODE
Remove the o-ring completely from the Airflow Tube OR roll it down to the
storage position as shown above to store it for on the go. To remove the o-ring
from its locking position, pinch the o-ring to create a bulge and push it off
sideways with your fingernail until it begins to rise up out of the groove.
DRAW RESISTANCE CONTROL
To adjust the DRC slowly start pulling out the Mouthpiece until it locks into
position as shown below. Locate the triangle on the Airflow Tube, then rotate
and adjust with your fingernail from the top grooves.
SECONDARY COOLING UNIT (SCU)
The SCU will increase the cooling capabilities of your Revolve Stem even further,
and it is especially useful with the Direct Airflow Tube.
To install, first remove the o-ring from the Storage Position, push the SCU in
place, then replace the o-ring.
If you would like to install the SCU and lock the spinning Mouthpiece at the
same time, use a second small o-ring (5x1mm) in the Locking Groove.
The SCU will provide the following modifiers to the guide values:
With DRC Airflow Tube:
+ 0.5 Cooling, - 0.5 Flavor
With Direct Airflow Tube:
+ 1 Cooling, - 0.5 Flavor
ALTERNATIVE SLEEVE OPTIONS
The Sleeves will affect the Cooling, Flavor and Sleeve temperature as follows:
GLASS SLEEVE
With DRC Airflow Tube:
+ 0.5 Flavor, - 2 Sleeve temp.
With Direct Airflow Tube:
- 1 Sleeve temp.
WOOD SLEEVE
With DRC Airflow Tube:
- 0.5 Cooling, - 3 Sleeve temp.
With Direct Airflow Tube:
- 2 Sleeve temp.
RECLAIM FILTER SCREEN
The optional removable Screen acts as a particulate filter as well as a collector
for some of the reclaim before it has a chance to condense on the Cooling Unit.
This extends the number of sessions before deep cleaning is required.
To insert the Screen, remove the Cooling Unit from the body and ‘snap’ the
Screen into position between the two posts at the end of the Cooling Unit .
Replace or clean regularly for the best experience.
MTL
DL
Choose either mouth-to-lung (MTL)
for slower and tighter draws or
direct-lung (DL) for powerful and
long draw with increased airflow.
The DL side has a single long deep
line, the MTL setting has 3 graduated
lines (deeper equals more open).
Pro tip - When the Screen is full you can place the whole thing in your next bowl for
a cheeky reclaim bonus.
Try the MTL side with the CLOSED option to further reduce the airflow.
Drawing too hard with MTL can cause excess condensation in the DRC tube.
