auto Call feature
The Auto Call feature is the part of the security system that calls the programmed phone
numbers if the sensors are triggered. By default, it is set to “on.” To change the Auto Call
feature “on” or “off”:
1. Enter your password followed by the [PROG] button to enter the programming mode.
2. Press the [#/DOWN] button until the symbol is flashing. Then select it by pressing
the [ARM/DISARM] button. Press the [#/Down] button to change it from on to off or
off to on.
3. Press the [ARM/DISARM] button to confirm your choice.
Call Cycle feature
The Security System is preset to call each person on your list for 3 cycles.Change the cycle
feature:
1. Enter your password followed by the [PROG] button to enter the programming mode.
2. Press the [#/DOWN] button until “CYCLE” is flashing. Then select it by pressing the
[ARM/DISARM] button. Press the [*/UP] or the [#/Down] button to change it from
1 to 5.
3. Press the [ARM/DISARM] button to confirm your choice.
Inbound Calling
The Security system accepts inbound calls, which enables you to control the unit by remote
control. The control unit is set up to answer calls by default after 5 rings. You can change
this to 3, 5, 7, or 10 rings. To change the number of rings:
1. Enter your password followed by the [PROG] button to enter the programming mode.
2. Press the [#/DOWN] button until the symbol is flashing. Then select it by pressing
the [ARM/DISARM] button. Press the [*/UP] or the [#/Down] button to change it to the
number of rings you would like the machine to answer on.
3. Press the [ARM/DISARM] button to confirm your choice.
remote Control Operation
This allows you to control the security system from a remote phone.
1. Call the phone number connected to the unit. The security system will answer after the
number of rings setup and it will make a beep tone.
2. Enter your password. You should hear 2 beep tones.
3. Enter “0” twice to put the Control Unit into the control mode.
4. Once it is in control mode, you can use any of the following telephone controls:
To listen in to the room press “*” twice,
To broadcast your voice press “#” twice,
To arm the system press “1” and your password then press “1,”
To disarm the system press “2,” and your password then press “2,”
To end the call press “*” then “0.”
Note:after30secondsitwillbeepawarningtone,after50secondsitwilldisconnect.You
maypress“0”twicetoputthesystembackintocontrolmodeatanytime.Youcanthen
reselectanoption.
baSIC OPeratIOnS
• To activate the security system without the remote type in your password followed by the
[ARM/DISARM] button.
• To deactivate the unit without the remote type in your password followed by the [ARM/
DISARM] button.
• The Panic Button: When you press the [PANIC] button on the control unit, or press and
hold the [PANIC] button for 2 seconds on remote control, the alarm will sound instantly for
30 seconds. At the same time, the Auto-Dialer will begin dialing the phone numbers you
programmed. To stop the alarm and the phone numbers from being dialed press your pass
-
word and the [ARM/DISARM] button on the control unit or hold the [DISARM] button on
the remote control for 2 seconds.
• Telephone controls: When the unit dials in response to the alarm, you need to press “0”
twice on the phone to enter into the control mode. If you do not enter “0”twice it will
eventually call the next number on the list. Once it is in control mode, you can use any of
the following commands:
To listen in to the room press “*” twice,
To broadcast your voice press “#” twice,
To disarm the system press “2” then your password then “2,”
To end the call press “*”then “0,”
• When the battery is running low the LED will flash once every 1.5 seconds to indicate the
low battery. When a wireless sensor’s battery is low, the LCD will show the battery icon
and the sensor zone number.
• When the battery is running low on the accessories, the LED light will go on for 3 seconds
and off for 1 second. Change batteries immediately to ensure continuous operation of the
security system.
aDDItIOnal featUreS
Siren feature
When the siren feature is on, the control unit will make an alarm noise when the security
system is activated and then call the phone numbers on your list. When the siren is turned
off, the security system will silently dial the phone numbers on the list so as to not alert the
intruder. The control unit is preprogrammed to the on position. To change the siren “on” or
“off”:
1. Enter the programming mode by typing your password followed by the [PROG] Button.
2. Press the [#/DOWN] Button until the symbol is flashing. Then select it by pressing
the [ARM/DISARM] button. Press the [#/Down] button to change it from on to off or
off to on.
3. Press the [ARM/DISARM] button to confirm your choice.
Page 6
Page 7
