to program the securIty code
1. Press the digits 0-0-0
2. Press the PRogRAM button
3. Enter your new code number (up to six digits)
4. Press the PRogRAM button again
to change exIstIng code
to a new code
1. Enter the old code number
2. Press the PRogRAM button
3. Enter your new code number (up to six digits)
4. Press the PRogRAM button again
to program the alarm tImIng
1. Press the PRogRAM button
2. Choose one of three options:
•
press 1
for 30 second alarm,
2 cycles, 30 seconds rest in between or;
•
press 2
for 60 second alarm,
2 cycles, 30 seconds rest in between or;
•
press 3
90 second alarm,
2 cycles, 60 seconds rest in between
The default setting is Option 1
to program the entry
delay tImIng
1. Press the PRogRAM button
2. Choose one of three options:
•
press 7
for 15 second delay
(default setting)
•
press 8
for 8 second delay
•
press 9
for 0 second delay/instant alarm
NOTE: For added protection the unit can only be
programmed when it’s set to the DISARM mode.
to arm the unIt
1. Enter your security code (or 0-0-0 if you did not
change the code)
2. Press the ARM button, you should hear 3 short
beeps to confirm that the unit is armed
NOTE:
• make sure the chime switch is set to OFF before
arming the unit
• There will be a beep after 60 seconds sensor warm-
up and exit delay after arming the unit
to dIsarm the unIt
1. Enter your security code
2. Press the DIsARM button, you should hear one
beep to confirm that the unit has been disarmed
actIvatIng the door chIme
1. slide the chime switch to on
2. Wait for 60 seconds after a beep for the sensor to
warm up
3. Whenever movement is detected the unit will sound
a “DIng-Dong” chime
4. slide the switch to off to deactivate the door
chime mode
NOTE: the door chime does not function when the unit
is in ARM mode
panIc Button
Pressing the PAnIC button triggers an immediate
30-second alarm. To stop the alarm enter your security
code and press the DIsARM button.
testIng the detectIon area
After selecting a location for installation of the unit,
turn the chime on and wait 60 seconds for the sen-
sor to warm up. Walk in front of the unit. When the
unit detects motion, the chime will sound. You can
determine the coverage by walking around the area.
There will be no chime sound if you walk beyond the
sensor’s range. By testing the detection range you can
adjust the location and the sensor head angle for best
coverage of the area you want. Turn the chime off
after you’ve tested the unit.
Battery low IndIcator
When in ARM mode the LED will flash once every 3
seconds to indicate when the battery is low. Change
the battery promptly to ensure proper functioning.
IntrusIon memory IndIcator
If there has been an intrusion while the unit was set to
ARM mode, it will be indicated by the LED flashing
three times when you DIsARM the system. Be sure to
check your home/office thoroughly after entering.
trouBle shootIng
cannot arm/disarm the unit
• Re-enter the security code to make sure it was
entered correctly
• if it still doesn’t work, remove the battery, wait three
minutes before replacing, and try again
If the
alarm sound is low
or the
sensor is not
detecting movement
, it
indicates that the battery is
low, replace battery promptly.
DIsCLAIMER: This unit can provide valuable protec-
tion for your home and property if utilized properly.
However, this unit cannot guarantee complete protec-
tion against burglary or robbery, therefore MsI will
not be held responsible for any loss or damages which
may occur.
®
�
