MacDon R116 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 234

background image

214713

65

Revision A

4.3

Installing Tractor Mating Hitch to Carrier Hitch

Depending on disc mower configuration, refer to the applicable installation procedure:

•

4.3.1 Installing Drawbar Hitch, page 65

•

4.3.2 Installing Two-Point Hitch (Cat. II) Adapter, page 69

4.3.1

Installing Drawbar Hitch

If attaching the disc mower to a tractor with a drawbar hitch, proceed as follows. If attaching the disc mower to a
tractor with a two-point hitch, refer to

4.3.2 Installing Two-Point Hitch (Cat. II) Adapter, page 69

.

1011296

B

A

Figure 4.21: Hitch End Packing

1.

Remove shipping wire or banding (A) securing shipping
blocks (B) at front of hitch, and remove blocks.

2.

Swivel lower gearbox until the input shaft is
facing forward.

1026323

B

C

A

D

Figure 4.22: Jack and Drawbar Hitch Packing

3.

Remove shipping wire (A) from the jack stand
support (D) and jack (B). Remove the jack stand
support and jack from the pallet. Leave the drawbar
hitch attached to the pallet.

4.

Remove the hardware bag from the jack stand support.

ASSEMBLING THE DISC MOWER (FACTORY-INSTALLED TRANSPORT)

«
...
71
72
73
74
75
...
»

Содержание R116











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R116

Бренд: Rath Страницы: 3

DVCPRO P2 Series

Бренд: Panasonic Страницы: 32

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: NAD Страницы: 10

Бренд: Parker Research Corp Страницы: 4

Бренд: Eastwood Страницы: 20

Бренд: Daihan Scientific Страницы: 43

Бренд: Dana Design Страницы: 20

Бренд: Jackco Страницы: 6

Бренд: Fellowes Страницы: 20

Бренд: P.Lindberg Страницы: 76

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды