MacDon R116 Скачать руководство пользователя страница 186

Страница: 186 / 234

214713

178

Revision A

9.3

Installing the Conditioner

CAUTION

Ensure spreader bar is secured to the forks so that it cannot slide off the forks or towards the mast while
detaching the conditioner from the mower.

NOTE:

If installing a finger conditioner, deflector plates must be removed. Refer to

9.2.1 Removing Cutterbar Deflectors,

page 177

NOTE:

Install deflector plates (A) when installing a roll conditioner and when replacing faulty or damaged deflector plates.
Refer to

9.3.1 Installing Cutterbar Deflectors, page 180

NOTE:

If you are replacing a roll conditioner and the deflector plates (A) are already installed on the machine, proceed to
Step

1, page 178

1015380

Figure 9.17: Conditioner Lift

Attach a spreader bar (A) to a forklift or equivalent lifting
device and attach chains to lugs (B) on the conditioner.
Use a chain rated for overhead lifting with a minimum
working load of 1135 kg (2500 lb.).

Lift conditioner and position it into disc mower opening.

1010997

Figure 9.18: Conditioner Pins

Carefully align pin (A) at each end of conditioner with
lug (B) on disc mower, and lower conditioner so that
pins (A) engage lugs (B) on disc mower.

CHANGING THE CONDITIONER

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды