MacDon R116 Скачать руководство пользователя страница 120

Страница: 120 / 234

214713

112

Revision A

5.8

Discharge Shield (No Conditioner)

•

If a conditioner is being installed, the discharge shield needs to be removed. Refer to

5.8.1 Removing Discharge

Shield (No Conditioner), page 112

•

If a conditioner is being removed, the discharge shield needs to be installed. Refer to

5.8.2 Installing Discharge

Shield (No Conditioner), page 114

5.8.1

Removing Discharge Shield (No Conditioner)

Follow these steps to remove the shielding installed on a mower configured without a conditioner:

1015037

Figure 5.45: Mower with Transport

Raise the mower fully and extend the center-link to
maximize the space between shield (A) and carrier
frame (B).

1023734

Figure 5.46: Lift Cylinder Lock-Out Valves

Close lift cylinder lock-out valves (A) on both sides of
the mower. Valve handles should be in the closed
position (90 degree angle to the hose).

SETTING UP THE TRACTOR

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды