MacDon R116 Скачать руководство пользователя страница 117

Страница: 117 / 234

214713

109

Revision A

5.6.2

Setting up Forming Shields for Roll Conditioner

Use these instructions to set up the forming shields on a machine with a roll conditioner.

1015019

Figure 5.38: Left Side Forming Shield

Remove and discard bolt (A) securing forming
shield (B) to frame.

Swivel shield (B) to the open position.

1015018

Figure 5.39: Adjuster Bar

Rotate clamp (B) until you can remove bolt (C).

Swing adjuster bar (A) and align with a hole on carrier
plate (D).

Install bolt through adjuster bar (A) and carrier plate (D).
Install clamp (B) onto bolt. Tighten clamp until shield
does not move.

Repeat above steps for opposite shield.

SETTING UP THE TRACTOR

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды