MacDon R113 SP Скачать руководство пользователя страница 208

Страница: 208 / 240

215009

194

Revision A

4.11.4

Replacing Header RPM Sensor

If the header rpm sensor malfunctions or is damaged, use this procedure to replace it.

Lower the header fully.

Shut down the engine, and remove the key from the ignition.

Remove the left driveshield. For instructions, refer to

Removing Driveshields, page 188

1024488

Figure 4.201: Header RPM Sensor

Remove plastic fastener (B) from the bracket and cut cable
tie (E) securing the sensor wire to the existing harness.

Disconnect wire harness (C) from speed sensor
connector (D).

Remove nut (F) from the end of the sensor and remove the
sensor from bracket (A).

Remove nut from the end of new sensor, install the new
sensor into bracket (C) securing with nut (F).

NOTE:

Ensure the speed sensor is correctly installed for the
windrower: use the bottom hole for M1 Series Windrowers;
use the top hole for M155

SP Windrowers.

Connect sensor wire (D) to harness (C).

Install plastic fastener (B) in the small hole in bracket (A).
Secure the sensor wire to fastener (B) with a cable tie,
allowing 102

–

104 mm (4

–

4 3/16 in.) between the fastener

and sensor.

10. Secure the sensor wire to header harness (C) with plastic

cable tie (E). Ensure the wires are clear of the belt and
pulley.

1024490

Figure 4.202: Header RPM Sensor

11. Adjust nuts (A) as required to achieve a 2

–

3 mm

(1/16

–

1/8 in.) gap (B) between sensor (C) and pulley (D).

Ensure the sensor face and the pulley face are parallel.
Bend bracket (E) as required.

12. Tighten nuts (A) to 12 Nm (9 lbf·ft).

13. Reinstall the driveshield. For instructions, refer to

Installing

Driveshields, page 190

14. Start the windrower, engage the header, and check the

operation of the speed sensor on the monitor. The sensor
may require re-calibrating. Refer to the windrower
operator

’

s manual for the calibration procedure.

MAINTENANCE AND SERVICING

Содержание R113 SP

















































































































































































































































Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды

MacDon R113 SP, Руководство оператора

Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды