MacDon R113 SP Скачать руководство пользователя страница 207 | Manualshive

Страница: 207 / 240

background image

215009

193

Revision A

4.11.2

Replacing Amber Hazard/Signal Light Fixture

WARNING

To avoid bodily injury or death from unexpected startup of machine, always stop the engine and remove the key from
the ignition before leaving the operator

’

s seat for any reason.

1.

Lower header fully.

2.

Shut down the engine, and remove the key from the ignition.

1027279

A

A

B

Figure 4.199: Amber Hazard Light

3.

Remove four nuts (A) and bolts (B) (only three shown)
securing the light to the bracket, and remove light.
Disconnect the light from the electrical harness.

4.

Connect the new light to the electrical harness.

5.

Position the new light on bracket with bolts (B), and install
and tighten four nuts (A).

6.

Check operation of the new light.

4.11.3

Replacing Amber Hazard/Signal Bulb

WARNING

To avoid bodily injury or death from unexpected startup of machine, always stop the engine and remove the key from
the ignition before leaving the operator

’

s seat for any reason.

1.

Lower the header fully.

2.

Shut down the engine, and remove the key from the ignition.

1021281

A

Figure 4.200: Plastic Lens and Screws

3.

Remove two Phillips screws (A) from the fixture, and
remove the plastic lens.

4.

Replace the bulb (trade #1157), and reinstall plastic the lens
and screws.

MAINTENANCE AND SERVICING

«
...
205
206
207
208
209
...
»

Содержание R113 SP

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R113 SP

Бренд: Kapriol Страницы: 32

Бренд: JABO Страницы: 4

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: Hammer Strength Страницы: 18

Бренд: Jacto Страницы: 12

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: Tar River Страницы: 44

Бренд: Tar River Страницы: 61

Бренд: Waters Страницы: 4

Бренд: Waterpik Страницы: 2

Бренд: Nady Audio Страницы: 2

Бренд: VaBroom Страницы: 4

Team Agile Color Tune TM16-0

Бренд: GRAU Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды