MacDon R1 FR Series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 238

background image

262391

34

Revision A

3.8

Detaching Rotary Disc Header from Tractor

Detach the rotary disc header from the tractor for servicing or storing.

3.8.1

Disconnecting the Tractor from Rotary Disc Header

The following procedure explains how to disconnect the tractor from the rotary disc header.

DANGER

To prevent bodily injury or death from the unexpected start-up or fall of a raised machine, stop the engine, remove the
key and engage the lift cylinder stops before going under the machine for any reason.

DANGER

Ensure that all bystanders have cleared the area.

1.

Park the machine on a flat, level surface.

2.

Shut down the engine, and remove the key from the ignition.

3.

Place blocks under each end, or just inside each end, of the cutterbar.

4.

Lower the header onto blocks.

5.

Ensure the auxiliary lift cylinders are fully retracted.

6.

Shut down the engine, and remove the key from the ignition.

7.

Turn the auxiliary lift cylinder lock-out valves to the closed position. For instructions, refer to

3.2.1 Locking and

Unlocking Auxiliary Lift Cylinders, page 22

.

ϭϬϰϯϲϴϳ

A

B

Figure 3.22: Auxiliary Lift Lock Pins

–

Left Side

8.

Retrieve the lift lock straight pins, washers, and Lynch pins
from storage location (B) on the left side of the carrier
frame, and install the straight pins into the holes (A) in lift
linkage on both sides of the header.

9.

Secure the straight pins with washers, and Lynch pins (2 per
pin) on both sides of the header carrier frame.

«
...
44
45
46
47
48
...
»

Содержание R1 FR Series















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 FR Series

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Backyard Play Systems Страницы: 64

Бренд: Haenim Страницы: 2

Бренд: Raymarine Страницы: 90

Бренд: Haaga Страницы: 31

Synthesis SDEC-3000

Бренд: JBL Страницы: 24

Бренд: Xilica Audio Design Страницы: 30

Бренд: Rane Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды