MacDon 338109 Скачать руководство пользователя страница 3

Страница: 3 / 32

Introduction

The Cutterbar kit (MD #338109) is used to replace the cutterbar on a MacDon R216 Rotary Disc Header. This document
explains how to install the kit. A list of parts included in the kit is provided in Chapter

2 Parts List, page 5

Installation time

Installation of this kit will take approximately 6 hours.

Conventions

The following conventions are used in this document:

•

Right and left are determined from the operator

’

s position. The front of the rotary disc header is the side that faces

the crop.

•

Unless otherwise noted, use the standard torque values provided in the rotary disc header operator

’

s manual and

technical manual.

NOTE:

Keep your MacDon publications up-to-date. The most current version of this instruction can be downloaded from our
Dealer-only site (

https://portal.macdon.com

) (login required).

NOTE:

This document is currently available in English only.

215339

Revision A

Содержание 338109

































Результаты поиска

Содержание 338109

Отзывы:

Похожие инструкции для 338109

Бренды по названию

Популярные бренды

MacDon 338109, Руководство по установке

Результаты поиска

Содержание 338109

Отзывы:

Похожие инструкции для 338109

Бренды по названию

Популярные бренды