Mac allister MLMP300H40 Скачать руководство пользователя страница 13

Страница: 13 / 24

MLMP300H40

detail

. . .

Getting

Started . . .

WARNING!

This quick start provides only a short overview of how to start

and stop the product! For safe use it is essential to read the entire instruction

Intended use

This petrol lawnmower MLMP300H40 is designated with a power output of 1.7 kW.
1. The product is intended for mowing grass in domestic gardens only. It must not be

used to mow unusually high, dry or wet grass (e.g. pasture grass) or for shredding
leaves.

2. For safety reasons it is essential to read the entire instruction manual before the

3. This product is intended for private domestic use only, not for any commercial use.

It must not be used for any purposes other than those described.

Handle adjustment

NOTE:

There are 3 locking holes on the handle supports of both sides.

Choose one of the holes to lock the lower handle bar (4) according to the
desired height of the handle (1).

1. Turn the lower handle bar lock (18) about 90 degrees (Fig. 10). Repeat on the

other side to unlock the lower handle bar (4).

2. Adjust the lower handle bar (4) to the desired height by aligning the pin of the

handle bar lock (18) with one of the handle support holes (Fig. 10).

3. Turn back the lower handle bar lock (18) and swing the lower handle bar (4) slightly

until the handle bar lock (18) clicks in place. Repeat on the other side to secure
the position of the lower handle bar (4) (Fig. 11).

Preparation

Assemble

Adjust

Add fuel

Add oil

Cold start

Press primer 3 to 5

times

Pull and hold

brake clutch

Pull recoil starter,

repeat until engine

starts

Operate

Warm start

Pull and hold

brake clutch

Pull recoil starter,

repeat until engine

starts

Operate

Stopping

Release brake

clutch

Storage

Empty fuel tank

Empty oil

Clean and

maintain

Store

Quick start / Product functions

Quick start

Содержание MLMP300H40

























Результаты поиска

Содержание MLMP300H40

Отзывы:

Похожие инструкции для MLMP300H40

Бренды по названию

Популярные бренды

Mac allister MLMP300H40, Руководство пользователя

Результаты поиска

Содержание MLMP300H40

Отзывы:

Похожие инструкции для MLMP300H40

Бренды по названию

Популярные бренды